AAON SS1068 Technical Manual Download Page 71

Page: 71 / 98

VCC-X Operator Interface SD

RSM STATUS

RSM-DIGITAL Status Screens

RSMD Status Screen #3 - Coil (Saturation)

Temp & Setpoint & Suction Pressure

RSMD #1-4 Status

Coil Temp: 0.0

Coil Setpt: 0.0

Suction Pr: XXX PSI

Line 2 Coil (Saturation) Temperature

If a Suction Pressure Transducer has been installed and

con

gured on the unit, the calculated Evaporator Coil

Suction (Saturation) Temperature will appear on this

line. If not, this line will display 0°F.

Line 3 Coil (Saturation) Temperature Setpoint

During DX dehumidi

cation, compressor(s) will be

staged/modulated to maintain this Coil Suction

(Saturation) Temperature Setpoint. If indoor humidity

reset of the Coil Setpoint has been con

gured, this will

be the current calculated setpoint.

Line 4 Suction Pressure

This is the current Suction Pressure.

RSMD Status Screen #4 - Head Pressure

Setpoint and Condenser Fan Signal

RSMD #1-4 Status

Head Pr: 0psi
Setpoint: 0psi
Cond Signal: 0.0%

Line 2 Head Pressure 1

If a Head Pressure Transducer is connected, this line

indicates the current Head Pressure reading.

Line 3 Head Pressure Setpoint

The current Head Pressure Setpoint.

Line 4 Condenser Signal

The current percentage signal being sent to

the Condenser Fan or Valve in order to maintain the

Head

Pressure

Setpoint.

RSMD Status Screen #5 - Alarms

RSM #1-4 Alarms

Active Alarms: No
See Active Alarms

on the RSM LCD

Line 2 Active Alarms

This screen will display Yes if there are active alarms.

Active alarms can be viewed on the LCD display of the

RSMD

Module.

Summary of Contents for SS1068



































































































Search results

Summary of Contents for SS1068

Reviews:

Brands by name

Popular brands

AAON SS1068, Technical Manual

Search results

Summary of Contents for SS1068

Reviews:

Brands by name

Popular brands