manualshive.com logo in svg

AAON SS1068, Technical Manual

Share
Download
AAON SS1068 Technical Manual Download Page 36

Zone

Zone

VCC-X CONFIGURATION

    VCC-X Operator Interface SD

36

Con

fi

 guration Screen #64 -   Broadcast  OA RH

VCC-X  Cnfg    ID #

Broadcast OA RH

 NO

USE < or > TO CHANGE

The VCC-X can broadcast its Outdoor Air Humidity Reading to 
other HVAC units if they are not equipped with their own Outdoor 
Air RH sensors. A network communications device (MiniLink PD 
or CommLink) is needed in order for this feature to operate. 

Select

 

YES for Broadcast Outdoor RH. 

Default is NO

. 

Con

fi

 guration Screen #65 -   Broadcast  Space 

Temperature

VCC-X  Cnfg    ID #

Broadcast SPC Temp

 NO

USE < or > TO CHANGE

The VCC-X can broadcast its Space Temperature Reading to other 
HVAC units if they are not equipped with their own Space Tem-
perature sensors. A network communications device (MiniLink PD 
or CommLink) is needed in order for this feature to operate. 

Select

 

YES for Broadcast Space Temperature. 

Default is NO

. 

Con

fi

 guration Screen #66 -   Broadcast  Space 

Humidity

VCC-X  Cnfg    ID #

Broadcast SPC RH

 NO

USE < or > TO CHANGE

The VCC-X can broadcast its Space Humidity Reading to other 
HVAC units if they are not equipped with their own Space Humid-
ity sensors. A network communications device (MiniLink PD or 
CommLink) is needed in order for this feature to operate. 

Select

 YES 

for Broadcast Space Humidity. 

Default is NO

. 

Con

fi

 guration Screen #67 -   Broadcast  CO

2

VCC-X  Cnfg    ID #

Broadcast CO2

 NO

USE < or > TO CHANGE

The VCC-X can broadcast its CO

2

 Reading to other HVAC units 

if they are not equipped with their own CO

2

 sensors. A network 

communications device (MiniLink PD or CommLink) is needed 
in order for this feature to operate. 

Select

 YES for Broadcast CO

2

. 

Default is NO

. 

Con

fi

 guration Screen #68 -    Broadcast  Building 

Pressure

VCC-X  Cnfg    ID #

Broadcast Build. Pr.

 NO

USE < or > TO CHANGE

The VCC-X can broadcast Building Pressure from this unit to any 
other unit requiring this value. 

Select

 YES for Broadcast Building 

Pressure. 

Default is NO

. 

Con

fi

 guration Screen #69 -    Broadcast to Boxes

VCC-X  Cnfg    ID #

Broadcast to Boxes

 NO

USE < or > TO CHANGE

The VCC-X can broadcast all applicable information and commands 
to the VAV Boxes. 

Select

 YES for Broadcast to Boxes. 

Default is NO

. 

Con

fi

 guration Screen #70-  #73 - Cool/Heat 

Stage Delays 

VCC-X  Cnfg    ID #

Cool Stage Delays
  Stage Up: 3 Min
Stage Down: 1 Min

VCC-X  Cnfg    ID #

Cool Stage Delays

Min Run: 5 Min
Min Off: 3 Min

VCC-X  Cnfg    ID #

Heat Stage Delays
  Stage Up: 3 Min
Stage Down: 1 Min

VCC-X  Cnfg    ID #

Heat Stage Delays

Min Run: 5 Min
Min Off: 1 Min

Both the Heating Stages and the DX Cooling Stages utilize  

Staging 

Up

 and 

Down

 Delay Periods between stages and  

Minimum Run

 

Times and 

Off

 Times. 

VCC-X Con

fi

 guration Screens

Summary of Contents for SS1068



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands