A&D AD-8922A Instruction Manual Download Page 36

Page: 36 / 42

１３

２

Function setting

The function setting "

aout

” is available only when the AD-8922A-06 is installed.

Class Item

Parameter

Description

2-digt output

Converts the consecutive 2 digits,
with the digit selected in

5el

as the

least, to voltage and outputs.

Analog output
mode

3-digt output

Converts the consecutive 3 digits,
with the digit selected in

5el

as the

least, to voltage and outputs.

Selects the first digit as the least.

Selects the second digit as the least.

Selects the third digit as the least.

Selects the fourth digit as the least.

Selects the fifth digit as the least.

aout

Analog
output

5el

Analog output
digit selection

Selects the sixth digit as the least.

Factory setting

Setting example

Notes

The invisible high-order digits are regarded as zero.

Summary of Contents for AD-8922A











































Search results

Summary of Contents for AD-8922A

Reviews:

Related manuals for AD-8922A

Brands by name

Popular brands

A&D AD-8922A, Instruction Manual

Search results

Summary of Contents for AD-8922A

Reviews:

Related manuals for AD-8922A

Brands by name

Popular brands