A&D AD-8922A Instruction Manual Download Page 15 | Manualshive

Page: 15 / 42

background image

13

５

TROUBLESHOOTING

Shown below is a list of various phenomena of the AD-8922A and the remedies.

Table 7

Phenomenon

Cause and remedy

error10

appears.

•

The communications settings of the AD-8922A and the weighing

instrument are not the same.

Check the settings.

error11

appears.

•

The weighing instrument data format is incorrect.

Set the data format to A&D standard format. Also check whether or not
data other than weighing data is output.

The bar display
remains and no
weighing data
appears.

•

Is the weighing instrument in the stream mode?

Only the stream mode displays the weighing data continuously. Other
modes display the data only when received. When the hold display is
selected in the AD-8922A function setting, the previous data received is
displayed until the next data is received.

•

Are the communications settings correct?

•

Is the cable correct?

The display flickers.

•

Electrical noises may affect the display.

Using the grounding terminal located on the rear of the AD-8922A,
ground the AD-8922A.

«
...
13
14
15
16
17
...
»

Summary of Contents for AD-8922A











































Reviews:

No comments

Related manuals for AD-8922A

Brand: Samson Pages: 92

Brand: Jafar Pages: 10

Brand: Abicor Binzel Pages: 8

Brand: Eaton Pages: 2

Brand: Kamstrup Pages: 36

Brand: JFA Electronicos Pages: 29

Brand: National Instruments Pages: 102

Brand: NAU ROBOTICS Pages: 109

Maschine Mikro MK2

Brand: Native Instruments Pages: 181

Brand: Parkside Pages: 65

Brand: YUGE Pages: 69

Brand: Quectel Pages: 232

Brand: Quectel Pages: 9

Brand: Quectel Pages: 73

FSDrive-MV1000 Series

Brand: YASKAWA Pages: 260

Brand: YASKAWA Pages: 114

Brand: YASKAWA Pages: 20

Brand: YASKAWA Pages: 152

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands