background image

3

SAFE INSTALLATION, USE, AND SERVICE

SAFE INSTALLATION, USE, AND SERVICE

Your safety and the safety of others is extremely important in the installation, use and servicing of this water heater. Many safety-

related messages and instructions have been provided in this manual and on your own water heater to warn you and others of 

a potential injury hazard. Read and obey all safety messages and instructions throughout this manual. It is very important that 

the meaning of each safety message is understood by you and others who install, use or service this water heater.

Many safety-related messages and instructions have been provided in this manual and on your own water heater to warn you and others of 

a potential injury hazard. Read and obey all safety messages and instructions throughout this manual. It is very important that the meaning 

of each safety message is understood by you and others who install, use, or service this water heater.

DANGER

WARNING

CAUTION

CAUTION

DANGER indicates an imminently

hazardous situation which, if not avoided,

will result in injury or death.

This is the safety alert symbol. It is used to alert you to

potential personal injury hazards. Obey all safety

messages that follow this symbol to avoid possible

injury or death. Keep this manual near the water heater.

WARNING indicates a potentially hazardous

situation which, if not avoided, could result

in injury or death.

CAUTION indicates a potentially hazardous

situation which, if not avoided, could result in

minor or moderate injury.

CAUTION used without the safety alert

symbol indicates a potentially hazardous

situation which, if not avoided, could result in

property damage.

All safety messages will generally tell you about the type of hazard, what can happen if you do not follow the safety message, and how 

to avoid the risk of injury.

IMPORTANT DEFINITIONS

Qualified Installer:

 A qualified installer must have ability equivalent to a licensed tradesman in the fields of plumbing, air supply, venting 

and gas supply, including a thorough understanding of the requirements of the 

Natural Gas and Propane Installation Code B149.1

 as it relates to 

the installation of gas fired water heaters. The qualified installer must also be familiar with the design features and use of flammable vapour 

ignition resistant water heaters and have a thorough understanding of this Installation and Operating manual.

Service Agency:

 A service agency also must have ability equivalent to a licensed tradesman in the fields of plumbing, air supply, venting 

and gas supply, including a thorough understanding of the requirements of the 

Natural Gas and Propane Installation Code” B149.1

 as it relates to 

the installation of gas fired water heaters. The service agency must also have a thorough understanding of this Installation and Operating 

manual, and be able to perform repairs strictly in accordance with the service guidelines provided by the manufacturer.

Gas Supplier: 

The Natural Gas or Propane Utility or service who supplies gas for utilization by the gas burning  appliances within this 

application. The gas supplier typically has responsibility for the inspection and code approval of gas piping up to and including the Natural 

Gas meter or Propane storage tank of a building. Many gas suppliers also  offer service and inspection of appliances within the building.

APPROVALS

APPROVALS

      

     

LOW LEAD

CONTENT

      

Summary of Contents for 100 Series

























































Reviews: