background image

SURFACE STEAMER SS-400TT

2

P/N 1011073 Rev. H 12/13 

McDonald’s

A.J. Antunes & Co.

CAUTION

All electrical connections must be in accordance 

with local electrical codes and any other appli-

cable codes.

WARNING

ELECTRICAL SHOCK HAZARD.  FAILURE TO 

FOLLOW THE INSTRUCTIONS IN THIS MANUAL 

COULD RESULT IN SERIOUS INJURY OR DEATH.

•  Electrical ground is required on this appliance.

•  Do not modify the power supply cord plug.  If 

it does not fit the outlet, have a proper outlet 

installed by a qualified electrician.

•  Do not use an extension cord with this unit.

•  Check with a qualified electrician if you are in 

doubt as to whether the appliance is properly 

grounded.

The Surface Steamer is manufactured from the finest 

materials available and is assembled to Roundup’s strict 

quality standards. This unit has been tested at the factory 

to ensure dependable trouble-free operation. 

Warranty Information

Please read the full text of the Limited Warranty in this 

manual. If the unit arrives damaged, contact the carrier 

immediately and file a damage claim with them. Save all 

packing materials when filing a claim. Freight damage 

claims are the responsibility of the purchaser and are not 

covered under warranty.

General

This manual is produced for the Surface Steamer.

The Surface Steamer is designed for the quick steaming 

and heating of buns. This design allows the operator to 

place buns on both sides of Surface Steamer at the same 

time. Water is superheated into steam, which penetrates 

the bun to heat it quickly and efficiently.
This manual provides the safety, installation, and operating 

procedures for the Surface Steamer. We recommend that 

this manual be read prior to installing and operating the unit. 

OWNER INFORMATION

IMPORTANT!  Keep these instructions for future reference.  If the unit changes ownership, 

 be sure this manual accompanies the equipment.

If you experience any problems with the installation 

or operation of your unit, contact A.J. Antunes & Co. 

Technical Support at 877-392-7854

Fill in the information below and have it handy when 

calling your Authorized Service Agency for assistance.  

The serial number is on the specification plate located 

on the side of the unit.

Purchased From:

Date of Purchase:

Model No.:

Serial No.:

Mfg. No.:

Refer to the service agency directory packaged with 

your manual and fill in the information below:

Authorized Service Agency

Name:

Phone No.:

Address:

Use only genuine Roundup replacement parts in this 

unit.  Use of replacement parts other than those sup-

plied by the manufacturer will void the warranty. Your 

Authorized Service Agency has been factory trained 

and has a complete supply of parts for this toaster.

You may also contact the factory at 1-877-392-7854  

(North America only), or 630-784-1000 if you have trou-

ble locating your local Authorized Service Agency.

To locate your nearest International Authorized Service 

Agency: log onto the McDonald’s web site: www.

mcdonalds.com and follow the on-screen directions. 

SERVICE/TECHNICAL ASSISTANCE

Summary of Contents for SS-400TT





















Reviews: