SURFACE STEAMER SS-400TT
9
P/N 1011073 Rev. H 12/13
McDonald’s
A.J. Antunes & Co.
MAINTENANCE
Daily Cleaning
1.
Turn off unit
. Turn the steamer’s power switch to
the off position. Unplug the power cord from the out-
let. Allow the unit to cool down for 30 minutes.
NOTE: Daily Cleaning should be performed after
close or during the breakfast menu (for 24-hour
stores).
2.
Clean the Bun Caps
. Open the Bun Caps. Clean
both sides of the Bun Caps with a clean, sani-
tized towel sprayed with EXCEED. Wipe the Bun
Caps with a clean, sanitized towel sprayed with
SolidSense Sanitizer Solution.
NOTE: Do NOT use no-scratch pads or steamer
brushes on plastic parts.
3.
Clean the Flipper
. Open the Flipper. Clean both
sides of the Flipper with a clean, sanitized towel
sprayed with EXCEED. Wipe the Flipper with a
clean, sanitized towel sprayed with SolidSense
Sanitizer solution. If required, use a no-scratch
pad to clean the flipper.
4.
Remove and clean the steamer Heat Shield
Pad
. Remove the steamer Heat Shield Pad.
Clean one side of the pad with a clean, sanitized
towel sprayed with EXCEED. Then wipe the
steamer Heat Shield Pad with a clean, sanitized
towel sprayed with SolidSense Sanitizer. Repeat
this step on the other side of the steamer Heat
Shield Pad.
WARNING
Turn the power off, unplug the power cord, and
allow the unit to cool down before performing any
service or maintenance.
CAUTION
Clean the Steam Generators with a damp paper
towel only. Do NOT use oily or dirty towels,
5.
Clean the Steam Generators and Diffusers.
Put
on neoprene gloves. Remove the diffusers. Clean
the Steam Generators with a paper towel damp-
ened with water. Make sure all crumbs and seeds
are removed from the generators. Clean the dif-
fusers with a clean, sanitized towel sprayed with
EXCEED. Wipe the diffusers with a clean, sani-
tized towel sprayed with SolidSense Sanitizer.
6.
Clean the top steamer surface.
Wipe the top
steamer surface with a clean, sanitized towel
sprayed with EXCEED. Wipe the top steamer
surface with a clean, sanitized towel sprayed with
SolidSense Sanitizer.
7.
Clean outside of steamer.
Wipe the entire out-
side of the steamer with a clean, sanitized towel
sprayed with EXCEED. Wipe the entire outside of
the steamer with a clean, sanitized towel sprayed
with SolidSense Sanitizer.
8.
Install the steamer Heat Shield Pad and
Diffusers.
Place the steamer Heat Shield Pat
on top of the steamer, reversing sides. Place the
Diffusers into the Steam Generators.
9.
Close the Flipper and Bun Caps.
Close the
Flipper and Bun Caps.
QUICK RECOVERY FOR POOR STEAM OUTPUT DURING
USE
The SS-400TT uses an open Heat/Steam Generator.
Water sprayed onto the Generator surface flashes into
steam immediately, but the minerals in the water stay on
the Generator surface. A small amount of mineral deposits
are needed for proper operation, but excessive deposits
cause poor steaming efficiency and excessive moisture,
which eventually hinders the steam action.
If the unit is not steaming correctly, follow this procedure to
improve steaming quality.
1. Pour 59 ml (2 ounces) of tap water into a clean
beverage cup.
2 Pour the water into both Steam Generators and
let it boil off.
NOTE: If needed, repeat steps 1 and 2 a few times.
This should result in a fine covering of minerals on the
steam generator.
