4RF Aprisa SRi User Manual Download Page 281 | Manualshive

Page: 281 / 353

background image

Managing the Radio | 281

Aprisa SRi User Manual 1.1.0

Monitored Parameter

Function

Broadcast Packets

Parameter to show the number of broadcast packets received from the customer into the
Ethernet port. Broadcast packets are good packets received that were directed to the
broadcast address. Note that this does not include multicast packets.

Multicast Packets

Parameter to show the number of multicast packets received from the customer into the
Ethernet port. Multicast packets are packets that were directed to a multicast address.
Note that this number does not include packets directed to the broadcast address.

VLAN Frames

Parameter to show the number of VLAN tagged frames received from the customer into
the Ethernet port, including filtering, congestion but excludes VLAN dropped packets

VLAN Frames Dropped

Parameter to show the number of VLAN tagged frames received from the customer into
the Ethernet port that were dropped due to filtered VLAN frames (filtering configuration
in VLAN configuration). L3 filtered packets, bad packets or congestion dropped packets
are not counted in this parameter.

Packet In Error

Parameter to show the number of errored packets received from the customer into the
Ethernet port caused by CRC errors, FCS Errors, alignment errors, oversized packets,
undersized packets, fragmented packets and jabber packets

Bytes In Error

Parameter to show the number of errored bytes received from the customer into the
Ethernet port

CRC / Alignment Error

Parameter to show the number of CRC / alignment errors received from the customer into
the Ethernet port. CRC / alignment errors are defined as frames that had a length
excluding framing bits, but including FCS octets of between 64 and 1518 octets, inclusive,
but had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS
Error) or a bad FCS with a non-integral number of octets.

Undersized Packets

Parameter to show the number of undersized packets received from the customer into the
Ethernet port. Undersized packets are less than 64 octets long excluding framing bits, but
including FCS octets.

Oversized Packets

Parameter to show the number of oversized packets received from the customer into the
Ethernet port. Oversized packets are longer than 1518 octets excluding framing bits, but
including FCS octets.

Fragmented Packets

Parameter to show the number of fragmented packets received from the customer into
the Ethernet port. Fragmented packets have either a bad Frame Check Sequence (FCS)
with an integral number of octets (FCS Error) or a bad FCS.

Jabber Packets

Parameter to show the number of jabber packets received from the customer into the
Ethernet port

Dropped Packets
(congestion)

Parameter to show the number of dropped packets received from the customer into the
Ethernet port due to congestion

Dropped Packets (filtering)

Parameter to show the number of dropped packets received from the customer into the
Ethernet port caused by packet L2 / L3 filtering

Dropped Bytes (filtering)

Parameter to show the number of dropped bytes received from the customer into the
Ethernet port caused by packet L2 / L3 filtering

«
...
279
280
281
282
283
...
»

Summary of Contents for Aprisa SRi


































































































































































































































































































































































Reviews:

No comments

Related manuals for Aprisa SRi

Brand: DBM Pages: 50

Brand: E-TOP Pages: 76

Brand: FOR-A Pages: 2

Brand: Enginko Pages: 19

Brand: Speedtouch Pages: 124

Brand: Netis Pages: 16

Brand: QNAP Pages: 54

Brand: Teletronics International Pages: 57

B-Control Fader BCF2000

Brand: Behringer Pages: 13

PD-9501-10GCO/AC

Brand: Microchip Technology Pages: 41

Brand: Hypercom Pages: 2

Brand: M-Audio Pages: 67

Brand: METREL Pages: 21

Brand: Allynk Technology Pages: 39

Brand: Allied Telesis Pages: 128

Brand: MikroTik Pages: 25

861W - Integrated Services Router Wireless

Brand: Cisco Pages: 34

Brand: Cisco Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands