3M Bair paws 875 Service Manual Download Page 1

Page: 1 / 33

Warning: Electrical Shock Hazard. There are electrically live parts within the

warming unit when it is connected to a power source, even when the handheld

temperature controller is in the OFF position.

Please forward to Biomedical Engineering Department

Bair Paws

™

Model 875 Warming Unit
Service Manual

Avertissement : risque d'électrocution. Certaines pièces à l'intérieur de l'appareil

sont sous tension lorsque ce dernier est branché sur une source d'alimentation,

même si le régulateur de température manuel est à l'arrêt.

À transmettre au département d'ingénierie biomédicale

Warnhinweis: Es besteht Stromschlaggefahr. Wenn das Erwärmungsgerät an das

Stromnetz angeschlossen ist, stehen bestimmte elektrische Komponenten auch

dann unter Strom, wenn die Schalter auf AUS gestellt ist.

Bitte weiterleiten an medizintechnische Abteilung

Check the 3M

Bair Paws

system website to ensure you have the most recent version of this document.

www.bairpaws.com reorder #202036A

Summary of Contents for Bair paws 875


































Search results

Summary of Contents for Bair paws 875

Reviews:

Related manuals for Bair paws 875

Brands by name

Popular brands

3M Bair paws 875, Service Manual

Search results

Summary of Contents for Bair paws 875

Reviews:

Related manuals for Bair paws 875

Brands by name

Popular brands