3M 3M-Matic Dual S-867 II Instructions And Parts List Download Page 44

Page: 44 / 62

Recommended Spare Parts

It is suggested that the following spare parts be ordered and kept on hand:

Qty.

Figure

Ref. No.

Part Number

Description

8-6

70-8601-0078-6

Blade – Serrated

8-7

78-8046-8594-5

Roller – Buffing

How To Order Replacement Parts

See Figures 8-1 - 8-9, in "Replacement Parts" section, to determine individual part and reference number.

Refer to the "Replacement Parts -- Illustrations and Parts Lists" section in this manual for part number and
description.

Note – The complete description has been included for standard fasteners and some commercially
available components. This has been done to allow obtaining these standard parts locally, should the
customer elect to do so.

Refer to first page of this instruction manual "Replacement Parts and Service Information", for replacement parts
ordering information.

Important –

Not all the parts listed are normally stocked items. Some parts or assemblies shown are

available only on a special order basis. Contact 3M/Tape Dispenser Parts (800-344-9883) to confirm item
availability.

Repair Service

Refer to the first page of this instruction manual "Service Instructions" for information on repair service.

Replacement Parts And Service Information

Summary of Contents for 3M-Matic Dual S-867 II































































Search results

Summary of Contents for 3M-Matic Dual S-867 II

Reviews:

Related manuals for 3M-Matic Dual S-867 II

Brands by name

Popular brands

3M 3M-Matic Dual S-867 II, Instructions And Parts List

Search results

Summary of Contents for 3M-Matic Dual S-867 II

Reviews:

Related manuals for 3M-Matic Dual S-867 II

Brands by name

Popular brands