3M 3M-Matic Dual S-867 II Instructions And Parts List Download Page 19

Page: 19 / 62

Intended Use ...............................................................................................................................

Equipment Warranty and Limited Remedy ..................................................................................

S-867 Contents ............................................................................................................................

Important Safeguards ...................................................................................................................

3 - 5

Specifications ...............................................................................................................................

Installation And Set-Up .................................................................................................................

7 - 10

Receiving and Handling ................................................................................

Machine Set-Up ...........................................................................................

Mounting ......................................................................................................

7 - 8

Air Regulator/Filter .......................................................................................

Tape Drum-Bracket Assembly ......................................................................

Theory of Operation ....................................................................................................................

11 - 14

General Information ......................................................................................

Operational Explanation ...............................................................................

11 - 13

Rest Position, Air Off ............................................................................

Rest Position, Air On ............................................................................

Application Cycle, Cut/Buff Sequence ...................................................

Application Cycle, Feed Sequence .......................................................

Components ................................................................................................

Valves ...................................................................................................

Cylinders ..............................................................................................

Operation .....................................................................................................................................

15 - 16

Tape Loading And Threading .......................................................................

15 - 16

Operating Sequence ....................................................................................

Adjustments .................................................................................................................................

Tape Width ...................................................................................................

Tape Web Alignment ....................................................................................

Tape Drum Tension ......................................................................................

Tape Tension Roller ......................................................................................

V-8 Valve Adjustment ...................................................................................

Air Flow Controls ..........................................................................................

Maintenance .................................................................................................................................

Blade Replacement ......................................................................................

Air Line Filter ................................................................................................

Instruction Manual

S-867 “L” Clip Applicator, Type 10500

Table of Contents

Page

(Table of Contents continued on next page)

Summary of Contents for 3M-Matic Dual S-867 II































































Search results

Summary of Contents for 3M-Matic Dual S-867 II

Reviews:

Related manuals for 3M-Matic Dual S-867 II

Brands by name

Popular brands

3M 3M-Matic Dual S-867 II, Instructions And Parts List

Search results

Summary of Contents for 3M-Matic Dual S-867 II

Reviews:

Related manuals for 3M-Matic Dual S-867 II

Brands by name

Popular brands