3M 3M-Matic Dual S-867 II Instructions And Parts List Download Page 38 | Manualshive

Page: 38 / 62

background image

18

Maintenance

1.

Release latch and open cover on right side of
S-867.

2.

Remove and retain blade guard mounting screws
(2), washers (2) and blade guard.

3.

Wrap old blades cutting teeth with tape to help
prevent injury.

4.

Remove and retain screws (2), washer (2), blade
alignment retainer, and remove and discard old
cutting blades (2).

5.

Wrap tape around replacement cutting blades (2)
teeth before installing.

6.

Install blades as shown with beveled side of blade
toward blade guard. Be sure blade is seated fully
against blade alignment retainer and then tighten
screws (2).

7.

Remove tape from blades and replace blade guard
(B) using screws (A) and plain washers (AA).
Tighten screws.

8.

Close and secure cover and connect/turn on
main air supply.

Blade Replacement

Refer to Figure 6-1

Air Line Filter

Refer to Figure 2-4. The air filter supplied with the
S-867 is equipped with an automatic drain. No
maintenance is required.

•

To reduce the risk associated with

sharp blade hazards:

−

Keep hands and fingers away from tape

cutoff blades under orange blade guards.
The blades are extremely sharp

WARNING

•

To reduce the risk associated with

pinch and entanglement hazards:

−

Turn air supply off and disconnect before

performing any adjustments,
maintenance or servicing the machine

WARNING

Figure 6-1 – Blade Replacement – Right Side View

«
...
36
37
38
39
40
...
»

Summary of Contents for 3M-Matic Dual S-867 II































































Reviews:

No comments

Related manuals for 3M-Matic Dual S-867 II

Brand: TANDBERG Pages: 16

Brand: uher Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands