6
7
Power
Permanently mounted, non-rechargeable .6- volt Lithium battery (factory
replaceable)
Battery Life
years from activation (maximum 6. alarm hours – minutes/day)
Radio Frequency Protection
<0% deviation of alarm level when subjected to 40MHz, Watt Radio
@ ft (6 cm)
Keypad
One button operation
Operating Temperature Range See table below
Sensor Accuracy (after
calibration)
Carbon Monoxide (CO) – Less than ± % of the displayed reading or
ppm, whichever is greater
Non-contaminated
environment
An environment containing less than 0. ppm of hydrocarbons, 0. ppm
of CO, 0. ppm of H
S, 0. ppm of Ammonia, 0. ppm of Hydrogen and
0. ppm of other gasses not normally found in the air.
Certified calibration gas*
Refers to a calibration gas sold by M or produced by an ISO 900:000
certified calibration gas manufacturer. The certified accuracy of the
calibration gas components must be listed on the calibration gas container
and traceable to National Institute of Standards and Technology (NIST) or a
national measurement institute standard reference material.
Warranty
years for sensor and electronics (see WARRANTY section)
* A gas analysis certificate of the calibration gas is available if requested.
Sensor
Symbol
Gas
Read by
Sensor
Display
Range
Reading
Resolution
Required
Calibration Gas
Concentration
User
Selectable
Alarm
Settings*
Factory
Set TWA
Alarm
Factory
Set
STEL
Alarm
Operating
Temperature
Range
CO
Carbon
Monoxide
0 - 99
ppm
ppm
ppm
, , 0,
00 ppm
ppm 00
ppm
-4 to ºF
(-0 to 0 ˚C)
*Factory default setting is ppm.
Display Menu Sequence
Press On/Off/Menu Button (number of times) Result
Unit performs a self-test
Display peak value
Enable/Disable calibration reminder function
4
Display alarm set points
6
Clear TWA values
7
Clear STEL values
Hold button down for seconds
Turn unit on or off
OPERATING INSTRUCTIONS
The following instructions are intended to serve as a guideline for the use of the M
™
Single Gas Monitor
0XLS Series, Carbon Monoxide (CO). It is not to be considered all-inclusive, nor is it intended to replace the
policy and procedures for each facility.
If you have any doubts about the applicability of the equipment to your job situation, consult an industrial
hygienist or call M at -800-4-460. In Canada, call Technical Service at -800-67-444.
Turning Unit On and Off
Press and hold the On/Off/Menu button for seconds to switch on/off.
During power up, the instrument will display the software version number and sensor type installed in the unit
and then perform a self-test. During the test sequence, the unit will display a 60 second countdown.
WARNING
WARNING
Using a certified gas with a concentration other than the one listed for this instrument and sensor when
conducting a calibration or calibration verification test (bump test) will produce inaccurate readings. This
means that higher levels of the gas being monitored may be present and could result in overexposure and
cause sickness or death
. For proper use, see supervisor or
User Instructions,
or call M in U.S.A.,
-800-4-460. In Canada, call Technical Service at -800-67-444.
Each person using this equipment must read and understand the information in these
User Instructions
before use. Use of this equipment by untrained or unqualified persons, or use that is not in accordance with
these
User Instructions,
may adversely affect product performance and
result in sickness or death.
This instrument helps monitor for the presence and concentration level of carbon monoxide gas. Misuse may
produce an inaccurate reading, which means that higher levels of the gas being monitored may be present
and could result in over exposure and
cause sickness or death.
For proper use, see supervisor or
User
Instructions,
or call M in U.S.A., -800-4-460. In Canada, call Technical Service at -800-67-444.
Use only for monitoring the gas which the sensor and instrument are designed to monitor. Failure to do
so may result in exposures to gases not detectable and
cause sickness or death
. For proper use, see
supervisor or
User Instructions,
or call M in U.S.A., -800-4-460. In Canada, call Technical Service at
-800-67-444.
SPECIFICATIONS
