3D Systems ProJet 1200 User Manual Download Page 44

Page: 44 / 46

3D Systems, Inc.

REPACKING

REPACKING THE PROJET 1200

At some point the ProJet 1200 may need to be moved or sent back for servicing . It is important to keep all the original packaging to

facilitate this process . Follow these steps to safety repack your ProJet 1200 .

1 .  Disconnect all cords from the ProJet 1200 .
2 .  Remove material cartridge as described on Page 15
3 .  If dummy cartridge was displaced during shipping, raise the cartridge lock

lever to the up position (if not already up), slide the dummy cartridge in and

place the cartridge lock lever to the down position .

4 . Apply a ~6 inch piece of painter’s tape (or any tape that does not leave a

residue) starting from the cartridge lock lever to the bottom of the machine .

Ensure the lever does not have any slack .

NOTE: Always wear nitrile gloves when installing or removing the

material cartridge to ensure no material spills onto skin .

5 . Place foam support piece that was taken out when machine was unpacked

in place as shown .

SERVICE AND SUPPORT

Should additional questions arise, contact your reseller either by phone or email:

Summary of Contents for ProJet 1200














































Search results

Summary of Contents for ProJet 1200

Reviews:

Brands by name

Popular brands

3D Systems ProJet 1200, User Manual

Search results

Summary of Contents for ProJet 1200

Reviews:

Brands by name

Popular brands