5
3D Systems, Inc.
CONSUMABLE SAFETY GUIDELINES
NOTE: Follow all safety rules in this section and observe all cautions and warnings in this guide .
VisiJet
®
FTX Material
There are 6 available Visijet FTX Materials, FTX Green, FTX Gold, FTX Silver, FTX Cast, FTX Clear, FTX Gray. Pay close attention to
the follow handling and disposal requirements .
FTX Material Cartridge
Uncured material waste is classified as regulated, and in some areas hazardous, thereby requiring special packaging, transportation
and disposal . Refer to your local environmental regulatory agency .
Applicable material “waste” includes cartridges (empty or full) . Any cleaning supplies used to clean up uncured material should be
disposed of in the same manner as the uncured material . To identify which disposal requirement applies, contact the local waste
disposal service provider. (The local environmental regulatory agency should have a list of qualified providers in your area.) Give the
disposal service provider a copy of the material’s MSDS and the SNUR (Significant New Use Regulation - U.S. only). The service will
provide a report, indicating the disposal requirements that apply, as well as a quotation for regularly scheduled pickups .
3D Systems assumes no liability or responsibility for proper disposal of the uncured material . Proper disposal of the uncured material is
the sole responsibility of the user .
VisiJet FTX Cartridge Removal
Wear protective gloves when removing the material tray from the printer . Remove the tray and place it in a disposable
bag. Be careful not to spill, drop or expose other materials to the waste.
NOTE: Partially used cartridges should be stored in a cool dark place, any light will cause the material to cure .
VisiJet FTX Material Disposal
ProJet 1200 3-D printer operators should be informed about the potential hazards of part material prior to performing operations which
may result in exposure to uncured material. This includes the removal and disposal of empty cartridges or unlikely spills that may occur
during operation .
Leaks indicate a serious malfunction. The first priority is to protect users from inadvertently touching the material. Handling uncured
material requires the use of gloves and other protective equipment to ensure there is no direct skin contact . If uncured spills occur,
promptly remove the spilled material, and dispose of the waste material according to local environmental regulations .
If a problem with the printer occurs, discontinue use until the problem is diagnosed . Resolve the problem before continuing to operate
the printer .
Small spills of uncured liquid can be cleaned up using disposable towels . After wiping the spill, wipe printer surfaces using a lint free
cloth and clean with Isopropyl alcohol or window cleaner .
Cleaning spills on carpeting can be difficult. Avoid placing printer over carpeted areas or use a barrier to avoid the possibility of carpet
damage . Advise any service provider involved (e .g . carpet cleaning service or disposal service) of the nature of the spilled material .
Provide the MSDS and other material information prior to their contact to the material . Provide material disposal requirements and
cleaning solutions if the material is uncured .
Tools that may be contaminated with the material should be cleaned prior to reuse . Recommended solvents such as IPA are normally
required to clean tools. A final wash with soap and water will remove any excess of print material.
VisiJet FTX Material Handling
Upon receipt of the part material shipment, inspect the carton for signs of physical damage and evidence of leakage on the exterior. If
leakage is observed, do not open carton; immediately contact 3D Systems’ Customer Support Hotline . If leakage is not present, store
materials in their material kits until they are ready to use . Materials should be kept indoors in a cool, dry area with adequate ventilation
with temperatures between 16°C (60°F) and 27 °C (80°F) . DO NOT EXCEED A MAXIMUM STORAGE TEMPERATURE OF 35°C
(95°F) .
Keep materials away from direct sunlight, heat, flames and other direct light or UV energy sources. For optimal results, keep stored
cartons closed and sealed until the cartridge is ready for use . Authorized 3D Systems VisiJet FTX Green Material should only be used
in the printer .
