3Com CoreBuilder 9000 ATM Interface Module Quick Start Manual Download Page 45

Page: 45 / 48

Confirmation Section

This section prompts you to save all changed parameters and asks if you
want to reboot.

To save the changes, enter Y, otherwise enter N.

To reboot, enter Y, otherwise enter N. The Main menu appears.

The Integrated Fast Setup of the ATM Switch Fabric Module and the ATM
Interface Module is now complete.

Finding More

Information

For more detailed information about the ATM Interface Module, see the

ATM Interface Module User Guide

For more detailed information about the ATM Switch Fabric Module, see
the

CoreBuilder 9000 Enterprise

ATM Switch User Guide

For more detailed information about the CoreBuilder 9000 Enterprise
Switch, see the

CoreBuilder 9000 Enterprise

Switch Getting Started

Guide.

Accept changes

--------------

*** Note: Change of some parameters will take effect now!!

Save changes (Y/N)? Y

Saving Network Prefix for next reboot...

Saving NNI parameters (effective from now on)...

The new configuration has been saved.

Reboot the system (Y/N)? n

The changes will take effect only after next reboot.

Summary of Contents for CoreBuilder 9000 ATM Interface Module

















































Search results

Summary of Contents for CoreBuilder 9000 ATM Interface Module

Reviews:

Related manuals for CoreBuilder 9000 ATM Interface Module

Brands by name

Popular brands

3Com CoreBuilder 9000 ATM Interface Module, Quick Start Manual

Search results

Summary of Contents for CoreBuilder 9000 ATM Interface Module

Reviews:

Related manuals for CoreBuilder 9000 ATM Interface Module

Brands by name

Popular brands