background image

|  Cassettes and Side Channels

7

OPTIONAL ACCESSORIES

Extension Brackets are used to project the shade up to 3” 

from the mounting surface. Extension brackets are available 

at an additional charge and are ideal if your shade must clear 

an obstruction such as a sliding glass door handle or window 

crank. Extension brackets require a flat vertical mounting 

surface of at least ⅞  ".

EXTENSION BRACKETS

To assemble and mount

•  Attach each mounting bracket to an extension bracket by 

using the nuts bolts and washers provided.

•  Mount the extension bracket to the wall per the instructions 

for an “Outside Mount”, using a level and making certain 

that all mounting brackets are level and project the same 

distance from the mounting surface. For maximum stability, 

install the screws diagonally from one another.

•  Install the shade per the directions for “Shade Installation”.

SPACERS

Spacers are available for use on windows with a projected 

molding. They are ⅜  " thick and allow the shade to be 

mounted flush with the outside edge of any standard window 

molding. They are available by contacting our Customer Care 

Department at 800-800-3329.

Hold down brackets are used primarily on shades mounted to 

doors or in motor homes. There are two small holes in the end 

caps. Use the pin on the hold down bracket to push through 

the hole in the end cap.

HOLD DOWN BRACKETS

•  With the shade lowered to it’s full length, place the pin of 

each hold down bracket into the hole in each end of the 

bottom rail.

•  Mark the mounting surface, either to the side or back of the 

window frame, through the holes in the hold down bracket. 

Make sure the hold down brackets are level and aligned with 

each other.

•  Raise the shade and screw the hold down brackets into the 

mounting surface using the screws provided.

•  Lower the shade and fl ex the 

hold down bracket outward 

so that the pin can be 

inserted into the hole in the 

end cap.

Summary of Contents for ROLLER SHADE









Reviews: