background image

|  Cassettes and Side Channels

5

INSTALLING SHADES WITH  

SIDE CHANNELS

•  Install the side guide ears. 

Ensure they fit flush with the 

outside of the endplates.

•  Add the side channel top 

and bottom caps onto the 

side channel pieces.

•  Before installing the side 

channels, lower the shade 

a little so you are able to 

insert the fabric into the 

caps guide.

•  Locate the side channel top 

cap to the side guide ear for 

the correct position. Lift out 

the fabric and bottom rail to 

insert the fabric into the  

side guides.

•  Slide the channels all the 

way up until they touch 

the bottom of the cassette. 

Hold a level on the siderails 

and adjust until it is level 

vertically. Then fasten with 

screws in the pre-drilled holes.

SHADE INSTALLATION

•  Before installing the face  

of the side channels, make 

sure the side guide locks  

are inserted.

•  Once those are inserted, 

the face of the side channel 

should snap into place.

•  Use a flat head screw 

driver and rotate the locks 

clockwise to secure the side 

guides together. 
NOTE: the channel cover 

in this image has been 

removed for clarity.

•  Test the shade to ensure it is 

operating correctly. Double 

check that the side channels 

are vertical and parallel 

using a level.

•  Run the shade down and up 

to ensure correct operation.

Unlocked Position: 

rotate clockwise  

to lock

Locked Position

Summary of Contents for ROLLER SHADE









Reviews: