ZyXEL Communications MES3500 Series Скачать руководство пользователя страница 74

Страница: 74 / 370

Chapter 7 System Status and Port Statistics

MES3500 Series User’s Guide

7.2.1 Status: Port Details

Click a number in the

Port

column in the

Status

screen to display individual port statistics. Use this

screen to check status and detailed performance data about an individual port on the Switch.

Link

This field displays the speed (either

10M

for 10Mbps,

100M

for 100Mbps or

1000M

for

1000Mbps) and the duplex (

for full duplex or

for half). It also shows the cable type

(

Copper

Fiber

) for the combo ports.

This field displays

Down

if the port is not connected to any device.

State

If STP (Spanning Tree Protocol) is enabled, this field displays the STP state of the port (see

Section 13.1 on page 115

for more information).

If STP is disabled, this field displays

FORWARDING

if the link is up, otherwise, it displays

STOP

LACP

This fields displays whether LACP (Link Aggregation Control Protocol) has been enabled on
the port.

TxPkts

This field shows the number of transmitted frames on this port.

RxPkts

This field shows the number of received frames on this port.

Errors

This field shows the number of received errors on this port.

Tx KB/s

This field shows the number of kilobytes per second transmitted on this port.

Rx KB/s

This field shows the number of kilobytes per second received on this port.

Up Time

This field shows the total amount of time in hours, minutes and seconds the port has been
up.

Clear Counter

Enter a port number and then click

Clear Counter

to erase the recorded statistical

information for that port, or select

Any

to clear statistics for all ports.

Table 9

Status (continued)

LABEL

DESCRIPTION

Содержание MES3500 Series



















































































































































































































































































































































































Результаты поиска

Содержание MES3500 Series

Отзывы:

Похожие инструкции для MES3500 Series

Бренды по названию

Популярные бренды

ZyXEL Communications MES3500 Series, Руководство пользователя

Результаты поиска

Содержание MES3500 Series

Отзывы:

Похожие инструкции для MES3500 Series

Бренды по названию

Популярные бренды