ZyXEL Communications MES3500 Series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 370

background image

Chapter 3 Hardware Overview

MES3500 Series User’s Guide

29

3.1.2.2 Auto-crossover

All ports are auto-crossover, that is auto-MDIX ports (Media Dependent Interface Crossover), so
you may use either a straight-through Ethernet cable or crossover Ethernet cable for all Gigabit port
connections. Auto-crossover ports automatically sense whether they need to function as crossover
or straight ports, so crossover cables can connect both computers and switches/hubs.

3.1.3 Transceiver Slots

These are slots for mini-GBIC (Gigabit Interface Converter) transceivers or 100 Mbps Small Form-
factor Pluggable (SFP) transceivers. A transceiver is a single unit that houses a transmitter and a
receiver. The Switch does not come with transceivers. You must use transceivers that comply with
the SFP Transceiver MultiSource Agreement (MSA). See the SFF committee’s INF-8074i
specification Rev 1.0 for details.

You can change transceivers while the Switch is operating. You can use different transceivers to
connect to Ethernet switches with different types of fiber-optic or even copper cable connectors.

To avoid possible eye injury, do not look into an operating fiber-optic
module’s connectors.

• Type: SFP connection interface
• Connection speed: 1 Gigabit per second (Gbps) or 1 Megabit per second (Mbps)

3.1.3.1 Transceiver Installation

Use the following steps to install a mini-GBIC transceiver (SFP module).

1

Insert the transceiver into the slot with the exposed section of PCB board facing down.

2

Press the transceiver firmly until it clicks into place.

3

The Switch automatically detects the installed transceiver. Check the LEDs to verify that it is
functioning properly.

4

Close the transceiver’s latch (latch styles vary).

5

Connect the fiber optic cables to the transceiver.

Figure 13

Transceiver Installation Example

«
...
27
28
29
30
31
...
»

Содержание MES3500 Series



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MES3500 Series

IntelliJack NJ200

Бренд: 3Com Страницы: 4

Parallel & Serial Port Checker PPC

Бренд: B&B Electronics Страницы: 4

Бренд: Tripp Lite Страницы: 3

Бренд: Patton electronics Страницы: 9

Бренд: Qlogic Страницы: 8

Бренд: Gira Страницы: 6

Бренд: Maipu Страницы: 80

Бренд: Eneo Страницы: 68

Бренд: Comelit Страницы: 19

Бренд: Buffalo Страницы: 2

Бренд: Idis Страницы: 16

JetNet 5720G-8P Series

Бренд: Korenix Страницы: 52

Бренд: Paradyne Страницы: 28

Бренд: Linksys Страницы: 44

Бренд: Crestron Страницы: 16

Бренд: MikroTik Страницы: 7

Бренд: Zhone Страницы: 2

ipscan probe 600

Бренд: Viascope Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды