ZyXEL Communications MES3500 Series Скачать руководство пользователя страница 194

Страница: 194 / 370

Chapter 25 Multicast

MES3500 Series User’s Guide

194

Figure 106

Advanced Application > Multicast > Multicast Setting > IGMP Snooping VLAN

The following table describes the labels in this screen.

Table 74

Advanced Application > Multicast > Multicast Setting > IGMP Snooping VLAN

LABEL

DESCRIPTION

Mode Select

auto

to have the Switch learn multicast group membership information of any

VLANs automatically.

Select

fixed

to have the Switch only learn multicast group membership information of the

VLAN(s) that you specify below.

In either

auto

fixed

mode, the Switch can learn up to 16 VLANs (including up to five

VLANs you configured in the

MVR

screen). For example, if you have configured one

multicast VLAN in the

MVR

screen, you can only specify up to 15 VLANs in this screen.

The Switch drops any IGMP control messages which do not belong to these 16 VLANs.

Note: You must also enable IGMP snooping in the

Multicast Setting

screen first.

Apply

Click

Apply

to save your changes to the Switch’s run-time memory. The Switch loses

these changes if it is turned off or loses power, so use the

Save

link on the top navigation

panel to save your changes to the non-volatile memory when you are done configuring.

Cancel

Click

Cancel

to begin configuring this screen afresh.

VLAN

Use this section of the screen to add VLANs upon which the Switch is to perform IGMP
snooping.

Name

Enter the descriptive name of the VLAN for identification purposes.

VID

Enter the ID of a static VLAN; the valid range is between 1 and 4094.

Note: You cannot configure the same VLAN ID as in the

MVR

screen.

Add

Click

Add

to insert the entry in the summary table below and save your changes to the

Switch’s run-time memory. The Switch loses these changes if it is turned off or loses
power, so use the

Save

link on the top navigation panel to save your changes to the non-

volatile memory when you are done configuring.

Cancel

Click

Cancel

to reset the fields to your previous configuration.

Clear

Click this to clear the fields.

Index

This is the number of the IGMP snooping VLAN entry in the table.

Содержание MES3500 Series



















































































































































































































































































































































































Результаты поиска

Содержание MES3500 Series

Отзывы:

Похожие инструкции для MES3500 Series

Бренды по названию

Популярные бренды

ZyXEL Communications MES3500 Series, Руководство пользователя

Результаты поиска

Содержание MES3500 Series

Отзывы:

Похожие инструкции для MES3500 Series

Бренды по названию

Популярные бренды