ZyXEL Communications MES3500 Series Скачать руководство пользователя страница 239 | Manualshive

Страница: 239 / 370

background image

MES3500 Series User’s Guide

239

C

H A P T E R

2 9

VLAN Mapping

This chapter shows you how to configure VLAN mapping on the Switch.

29.1 VLAN Mapping Overview

With VLAN mapping enabled, the Switch can map the VLAN ID and priority level of packets received
from a private network to those used in the service provider’s network.

The Switch checks incoming traffic from the switch ports (non-management ports) against the
VLAN mapping table first, the MAC learning table and then the VLAN table before forwarding them
through the Gigabit uplink port. When VLAN mapping is enabled and incoming tagged packets do
not match any entry in the VLAN mapping table, the Switch forwards the tagged packets according
to its VLAN tag that do not match an entry in the VLAN mapping table. If the incoming packets are
untagged, the Switch adds a PVID based on the VLAN setting.

Note: You can not enable VLAN mapping and VLAN stacking at the same time.

29.1.1 VLAN Mapping Example

In the following example figure, packets that carry VLAN ID 12 and are received on port 3 match a
pre-configured VLAN mapping rule. The Switch translates the VLAN ID from 12 into 123 before
forwarding the packets. Any packets carrying a VLAN tag other than 12 (such as 10) and received
on port 3 will be forwarded in the individual VLAN network respectively (such as VLAN 10).

Figure 141

VLAN mapping example

29.2 Enabling VLAN Mapping

Click

Advanced Application

and then

VLAN Mapping

in the navigation panel to display the

screen as shown.

Port 3

12

10

123

10

Service Provider

Network

«
...
237
238
239
240
241
...
»

Содержание MES3500 Series



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MES3500 Series

DES-3526 - Switch - Stackable

Бренд: D-Link Страницы: 258

S5500-HI Switch Series

Бренд: H3C Страницы: 180

Бренд: H3C Страницы: 84

Бренд: H3C Страницы: 281

Бренд: H3C Страницы: 8

Бренд: H3C Страницы: 9

Бренд: H3C Страницы: 33

Бренд: H3C Страницы: 42

Бренд: H3C Страницы: 102

S12500CR Series

Бренд: H3C Страницы: 9

Бренд: H3C Страницы: 15

H3C S7500E Series

Бренд: H3C Страницы: 1565

Бренд: H3C Страницы: 4

Бренд: Klark Teknik Страницы: 50

MasterBus Tanklevel Interface

Бренд: Mastervolt Страницы: 8

LinkSmart KW6515

Бренд: Kasda Страницы: 31

Dimension ES-3124

Бренд: ZyXEL Communications Страницы: 228

Бренд: QNAP Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды