ZyXEL Communications GS1200 SERIES Скачать руководство пользователя страница 67

Страница: 67 / 85

GS1200 Series User’s Guide

HAPTER

Troubleshooting

This chapter offers some suggestions to solve problems you might encounter. The potential problems are
divided into the following categories.

•

Power, Hardware Connections, and LEDs

•

Switch Access and Login

•

Switch Configuration

15.1 Power, Hardware Connections, and LEDs

The Switch does not turn on. None of the LEDs turn on.

Make sure you are using the power adapter or cord included with the Switch.

Make sure the power adapter or cord is connected to the Switch and plugged in to an appropriate
power source. Make sure the power source is turned on.

Disconnect and re-connect the power adapter or cord to the Switch.

If the problem continues, contact the vendor.

One of the LEDs does not behave as expected.

Make sure you understand the normal behavior of the LED. See

Section 3.3 on page 18

Check the hardware connections. See

Section 15.1 on page 67

Inspect your cables for damage. Contact the vendor to replace any damaged cables.

Disconnect and re-connect the power adapter or cord to the Switch.

If the problem continues, contact the vendor.

The

PoE

LED is off and/or power is not being supplied to my PoE-enabled device. (For GS1200-5HP

v2 and GS1200-8HP v2)

Содержание GS1200 SERIES






















































































Результаты поиска

Содержание GS1200 SERIES

Отзывы:

ZyXEL Communications GS1200 SERIES, Руководство пользователя, Страница: 67 / 85

Результаты поиска

Содержание GS1200 SERIES

Отзывы: