ZDAS-16CA SERIES PROGRAMMING GUIDE
--------------------------------------------------------------------------------------------------------------------------------------------------------
PAGE
13
OF 19
“Dis-Arm” status once the Access Zone is triggered; system will restore “ARM
“ status if it’s no trigger of this special zone); Factory setting is “0”
(Note: “1”, “2”, “4” , “6” zone type is 24-hour ARM status, not effected by ARM or DIS-ARM
operation.
Siren status: 0 alarm without sound; 1 sound alarm, factory setting is “1”
4.9 Set Boundary(Home) Arm
（
Only for ZDAS-16CA-8/16CA-16/16CA/8CA
）
Format: 19 + Zone number (2 bit) + 0/1(0 close, 1 open)+
(Zone number: 01~16)
4.10 Doorbell function setting
（
Only for ZDAS-16CA-8/16CA-16/16CA/8CA
）
Format: 60 + Zone Number (1 bit) + 0/1 +
(confirm key)
（
zone number:1~8
）
“1” open, “0” close Factory setting is “0”), when zone set as Door-Bell zone, it will be Doorbell
function in DIS-ARM status, zone will restore normal in ARM status.
Note: The 8th Zone is defined as fixed doorbell zone. The 8th zone will not be affected by set
Arm or Dis-Arm if it’s set as doorbell zone.
4.11 Set User Code (Alarm Center Code)
Format: 31
＋
4 bit User code
＋
(Confirm Key);
Delete User Code: 32
＋
(Confirm Key)
；
4 bit user code is allocated the entering code for alarm center.
Note: Don’t use this operation if not connect with alarm center.
4.12 Set ARM Delay(Exit Delay) Time
Format: 40
＋
Time(3 bit)
＋
(Confirm Key)
Time: 000
～
255 seconds
4.13 Set Alarm Delay(Entry Delay) Time
Format: 43
＋
Time(3 bit)
＋
(Confirm Key)
Time: 000
～
255 seconds
4.14 Set Telephone Number
1. Set Central alarm telephone number
Format: 50
＋
Telephone Number
＋
(Confirm Key)
(Don’t use this operation if not connect
with alarm center.)
Delete center telephone number: 50
＋
(Confirm Key)
2
．
Set User alarm telephone number
Format: 5+ group of phone number (1bit)+phone
(Confirm Key)
Group of phone number: 1-6 means: 1
st
to 6
th
group telephone number.
3. Delete User alarm telephone number
Format: 5+ group of phone number (1bit)
+
(Confirm Key)
4
．
Set telephone number for connecting internal line to external line
Format: 5+ group of telephone number (1bit) + Preset number in Program control exchange
machine (the preset number is the additional dialing number such as 0 or 9 etc before you dial
external line from internal line) +
+ phone
(Confirm Key)
Group of telephone number: 1~6 means: 1
st
to 6
th
group telephone number
Note: The system will auto-dial preset telephone number cycled for 10 times until confirmed when
accident happen. Alarm center phone number will not be stopped dialing after Dis-Arm, but user
alarm number will stop dialing immediately after Dis-Arm.
4.15 Set 7 Groups Telephone Format
Format: 77 + group of telephone number (0-6) + Format (1 bit)
(group 0~6 correspond 50-56)
Format: “0” “1” is center communication protocol (“0” CID, “1” program 4+2), “5” user’s
telephone, ”6”
ARM
telephone,”7”
Dis-Arm
telephone, “8” Regular checking
Format after reset: “0” is 0, “1--6” group is 5
