background image

2

• 

Do not touch the fan or moving parts and do not place any objects or your fingers 

in the vicinity of the moving parts during operation of the appliance. Moving parts 

can cause serious injury or even death.

WARNINGS ASSOCIATED WITH ELECTRICAL APPLIANCES

• 

The electrical supply to the appliance must be protected by a 30 mA differential 

Residual  Current  protection  Device  (RCD),  complying  with  the  standards  and 

regulations in force in the country in which it is installed.

• 

Do  not  use  any  extension  lead  when  connecting  the  appliance;  connect  the 

appliance directly to a suitable power supply circuit.

• 

Before carrying out any operations, check that:

 

- The  voltage  indicated  on  the  appliance  information  plate  corresponds  to  the 

mains voltage.

 

-

The power grid is adapted to the power requirements of the appliance, and is 

grounded. 

• 

In  the  event  of  anormal  operation  or  the  release  of  unusual  odours  from  the 

appliance, turn it off immediately, unplug it from its power supply and contact a 

professional.

• Before any access to the appliance for service or maintenance, ensure that it is 

switched off and completely disconnected from the power supply. Furthermore, in 

addition to confirming that the heating priority (where applicable) is deactivated, 

ensure that any other equipment or accessories connected to the appliance are 

also disconnected from the power supply circuit.

• Do not disconnect and reconnect the appliance to the power supply when in 

operation.

• 

Do not pull on the power cord to disconnect it from the power supply.

• 

If the power cord is damaged, it must be replaced by the manufacturer, its technician 

or a qualified person to guarantee safety.

• 

Do not perform maintenance or servicing operations on the appliance with wet 

hands or if the appliance is wet.

• 

Before connecting the appliance to the source of supply, ensure that the terminal 

block or supply socket to which the appliance will be connected is in good condition 

and is not damaged or corroded in any way.

• 

For  any  component  or  sub-assembly  containing  a  battery:  do  not  recharge  or 

dismantle the battery, or throw it into a fire. Do not expose it to high temperatures 

or direct sunlight.

• In stormy weather, disconnect the appliance from the power supply to prevent it 

from suffering lightning damage.

• 

Do not immerse the appliance in water (with the exception of cleaners) or mud.

WARNINGS CONCERNING APPLIANCES CONTAINING R32 REFRIGERANT

• 

This device contains R32 refrigerant, a class A2L refrigerant, which is considered to 

be potentially flammable.

• 

Do not discharge R32 fluid into the atmosphere. These are fluorinated greenhouse 

effect gases, covered by the Kyoto Protocol, with a Global Warming Potential (GWP) 

= 675 (EU Regulation No. 517/2014).

• 

In order to comply with relevant environmental and installations standards and 

regulations such as, but not limited to, French decree No. 2015-1790 and/or the EU 

Regulation EU 517/2014, the cooling circuit must be checked for leakage at least 

once a year. This operation must be carried out by a certified cooling appliance 

specialist.

• 

The device must be stored in a ventilated place away from all sources of fire.

• 

Install the unit outdoors.  Do not install the unit indoors or in an enclosed, non-

ventilated area outdoors.

• 

Do not use means to accelerate the defrosting process or to clean, other than those 

recommended by the manufacturer.

• 

The appliance shall be stored in a room without continuously operating ignition 

sources  (for  example:  open  flames,  an  operating  gas  appliance  or  an  operating 

electric heater).

• 

Do not pierce or burn.

• 

Be aware that R32 refrigerants may not contain an odour.

Содержание Z200
























Отзывы: