background image

H0412500.A - EN - 2013-02

5

2.2 Installing the TRi pH or TRi PRO module

•  

Turn  off  your  Zodiac  TRi  salt  chlorina

-

tor and then filtration by cutting off the 
main  electricity  supply  in  order  to  iso

-

late the installation.

•  

Close  the  isolating  valves  in  the  pipe

-

work.

•  

Remove the silver cover by pressing the 
sides  and  raising  it,  then  unscrew  the 
four screws attaching the original (emp

-

ty) lower module to the main unit.

•  

Remove the empty module and offer up 
the TRi pH or TRi PRO module. 

•  

Connect  the  ribbon  cable  from  the  TRi 
pH or TRi PRO to the connector on the 
TRi power pack. 

•  

Put the TRi pH or TRi PRO module in po

-

sition,  replace  the  four  screws  and  re

-

place the silver cover.

•  

Do not reconnect the electricity supply until the TRi pH or TRi PRO module, the sensor-holding POD and the pH 
minus injection pipe have been installed (see § 2.3.3).

•  

Always wait 2 minutes, particularly when performing any technical work, between disconnecting the TRi from 
the mains electricity supply and connecting the TRi pH or TRi PRO module.

2.3 Installing the POD

The sensor-holding POD is a single assembly including the flow rate detector (used by your TRi chlorinator, see § 2.3.2), 
the pH and ACL sensors and pH minus injection.

•  

The TRi unit bypass valves must always be open.

•  

The sensor-holding POD must always be positioned on a horizontal pipe so that the sensors are vertical.

•  

The POD must be the first unit fitted after the pool filter.

•  

If the pool is fitted with a heating system (heat pump, heat exchanger, electric heater, etc.), the POD must be 
installed before it (to take readings on unheated water).

•  

We recommend positioning the POD more than 20 cm from an elbow in the pipe.

•  

The sensor cables must not be positioned near high voltage mains electricity cables.

pH sensor

Flow switch

Water circulation direction

pH minus injection

ACL sensor

A badly-installed sensor may give false readings and cause inappropriate operation of the TRi unit. Neither the 
manufacturer nor the unit shall be liable in this event.

Содержание TRi pH Module















Отзывы: