Zodiac POWER FORCE 25 Скачать руководство пользователя страница 15

Страница: 15 / 20

4.2 I Error code display

Display

Possible causes

Solutions

Resetting

Exchanger protection

in cool mode

ST4 sensor temperature too low Wait until the exterior temperature

rises

Automatic

High temperature

error on evaporator in

"cooling" mode

ST3 sensor temperature over

60°C or evaporator scaled up

Clean the evaporator, if problem

persists, call an approved technician

Automatic if

ST3 sensor

temperature below

450C

Phase order fault

Cabling not respected on the

appliance's supply terminals,

Invert phases on power terminals

(appliance switched off )

By electricity

supply

disconnection or

by pressing

Electricity provider has changed

the order of the phases

Contact the electricity provided to

find out if your installation has been

modified.

Temporary disconnection of the

power supply to one or more

phases

Low pressure fault on

cooling circuit

Pressure fault in the low

pressure circuit (if problem

persists after resetting)

Call an approved technician

Automatic (if fewer

than 4 faults per

hour) or press

Cooling circuit high

pressure fault

Water condenser scaled up

Clean the water condenser

Automatic (if fewer

than 4 faults per

hour) or press

Insufficient water flow

Increase flow using by-pass, check

that the pool filter is not clogged

Air and water emulsion passed

into the device

Check the pool's hydraulic

circuit

Flow controller blocked

Check the flow controller

Compressor discharge

temperature fault

Compressor discharge

temperature too high

Call an approved technician

Press

for 3

seconds

ST1 sensor fault

water intake sensor

Sensor is faulty or offline

(J12-A1 connector)

Reconnect or change the sensor

Cut power or press

ST4 sensor fault fluid

line sensor

Sensor is faulty or offline (J8-A1

connector)

Reconnect or change the sensor

By electricity

supply

disconnection or

automatic if the

fault disappears

ST3 sensor fault

Defrost sensor

Sensor is faulty or offline

(terminals 1-2 connector J3-A2)

Reconnect or change the sensor

Cut power or press

ST sensor fault air

intake sensor

Sensor is faulty or offline

(terminals 3-4 connector J3-A2)

Reconnect or change the sensor

Cut power or press

Содержание POWER FORCE 25





















Результаты поиска

Содержание POWER FORCE 25

Отзывы:

Похожие инструкции для POWER FORCE 25

Бренды по названию

Популярные бренды

Zodiac POWER FORCE 25, Инструкция по установке и эксплуатации

Результаты поиска

Содержание POWER FORCE 25

Отзывы:

Похожие инструкции для POWER FORCE 25

Бренды по названию

Популярные бренды