Zodiac POWER FORCE 25 Скачать руководство пользователя страница 16

Страница: 16 / 20

Display of

Possible causes

Solutions

Resetting

ST5 sensor error

compressor discharge

sensor

Sensor is faulty or offline (J7-A1

connector)

Reconnect or change the sensor

By electricity

supply

disconnection or

automatic if the

fault disappears

Communication

fault between the

regulation board and

the display board

Bad connection between the A1

and A2 boards

Check the J8, J9, J7 and J4-

J5 connectors on the link cable

between the boards

By electricity

supply

disconnection or

automatic if the

fault disappears

Board power supply fault

Check the boards' power supply

Faulty boards

Replace the boards

Ventilation command

fault

Lack of information on the fan

speed

Call an approved technician

Cut power or press

Communication fault

with the A3 ventilation

board

Poor connections

Check the connections

By electricity

supply

disconnection or

automatic if the

fault disappears

Power supply fault

Check the power supply

Incorrect configuration

Check the position of switches

SW1 and SW2 and the JPC bridge

Board out of service

Replace the board

4.3 I Additional menus

To access the menu, press

To browse the menus and modify the values, press

To exit the menu, press

You may consult the latest faults:

You may read the values measured by the sensors and the operation of the electronic valve and the fan.

Water temperature on intake

Air temperature

Defrost sensor

Fluid line sensor

Compressor discharge temperature

Opening of electronic valve

Fan operating speed

Содержание POWER FORCE 25





















Результаты поиска

Содержание POWER FORCE 25

Отзывы:

Бренды по названию

Популярные бренды

Zodiac POWER FORCE 25, Инструкция по установке и эксплуатации

Результаты поиска

Содержание POWER FORCE 25

Отзывы:

Бренды по названию

Популярные бренды