Zodiac CX35 Скачать руководство пользователя страница 17

Страница: 17 / 20

Section 5. Troubleshooting

5.1 Using the Information LED

The information LED

on the Control box flashes in a specific sequence to indicate one of three possible

cleaner malfunctions.

LED Flashing

Cause

Solution

1 Flash

LED flashes once

Floating cable may not be plugged

into the Control box correctly.

Unplug the floating cable from the

Control box and reconnect.

If the problem persists, contact

Zodiac Customer Service at

1300 763 021

2 Flashes

LED flashes twice

Cleaner wheels may be jammed

or brushes may be blocked with

debris.

Turn cleaner wheels to ensure

they are not jammed.

Check brushes for debris.

Start a new cleaning cycle.

If the problem persists, contact

Zodiac Customer Service at

1300 763 021.

3 Flashes

LED flashes three

Pump axis or propeller may be

jammed with debris.

Dirty filter.

Check the pump axis for debris.

Check propeller for debris.

Clean the filter.

Start a new cleaning cycle.

If the problem persists, contact

Zodiac Customer Service at

1300 763 021.

H0574000_REVA

Содержание CX35





















Результаты поиска

Содержание CX35

Отзывы:

Похожие инструкции для CX35

Бренды по названию

Популярные бренды

Zodiac CX35, Руководство пользователя

Результаты поиска

Содержание CX35

Отзывы:

Похожие инструкции для CX35

Бренды по названию

Популярные бренды