background image

BG300 Barrier Gate 

User Manual 

P a g e

 | 

2  

 

 Copyright©2022 ZKTECO CO., LTD.  All rights reserved. 

ZKTeco  does  not  assume  responsibility  for  any  errors  or  omissions  in  the  information  or 

documents which are referenced by or linked to this manual. The entire risk as to the results 

and performance obtained from using the information is assumed by the user. 

ZKTeco  in  no  event  shall  be  liable  to  the  user  or  any  third  party  for  any  incidental, 

consequential, indirect, special, or exemplary damages, including, without limitation, loss of 

business, loss of profits, business interruption, loss of business information or any pecuniary 

loss, arising out of, in connection with, or relating to the use of the information contained in 

or  referenced  by  this  manual,  even  if  ZKTeco  has  been  advised  of  the  possibility  of  such 

damages.  

This  manual  and  the  information  contained  therein  may  include  technical,  other 

inaccuracies  or  typographical  errors.  ZKTeco  periodically  changes  the  information  herein 

which will be incorporated into new additions/amendments to the manual. ZKTeco reserves 

the  right  to  add,  delete,  amend,  or  modify  the  information  contained  in  the  manual  from 

time to time in the form of circulars, letters, notes, etc. for better operation and safety of the 

machine/unit/equipment.  The  said  additions  or  amendments  are  meant  for  improvement 

/better operations of the machine/unit/equipment and such amendments shall not give any 

right to claim any compensation or damages under any circumstances. 

ZKTeco shall in no way be responsible (i) in case the machine/unit/equipment malfunctions 

due  to  any  non-compliance  of  the  instructions  contained  in  this  manual  (ii)  in  case  of 

operation of the machine/unit/equipment beyond the rate limits (iii) in case of operation of 

the  machine  and  equipment  in  conditions  different  from  the  prescribed  conditions  of  the 

manual. 

The  product  will  be  updated  from  time  to  time  without  prior  notice.  The  latest  operation 

procedures and relevant documents are available on 

http://www.zkteco.in.

 

If there is any issue related to the product, please contact us. 

ZKTeco Biometric India Pvt Ltd. 

Address

 

B-1, Khata No.31, Devasandra Industrial Estate,  

Whitefield Main Road, Beside Phoenix Mall, 

 

               

 Mahadevapura, Bengaluru, Karnataka. 

Phone 

080 8628 1342 

For business-related queries, please write to us a

[email protected].

 

To know more about our global branches, visit 

www.zkteco.in.

 

 

 

Содержание BG300






























Отзывы: