background image

16

13 Maintenance

Maintenance-free operation of the product is guaranteed for up to 10 million cycles.
Maintenance-free operation of the product can be reduced under the following circumstances:
•  Operation with impermissible compressed air
•  Dirty environment
• 

Improper use and use that does not comply with the power specifications.

•  Permissible temperature range not observed

 

Even though the product is maintenance-free as mentioned above, perform a regular visual inspection to check for any 

damage or contamination.

 

Have maintenance work be performed by Customer Service whenever possible.

 

Ö

Dismantling and reassembling the product without authorization may result in complications, as special installation 

equipment is required in some cases. Zimmer GmbH accepts no liability for any resulting malfunctions or damage.

14 Decommissioning/disposal

INFORMATION

When the product reaches the end of its operational phase, it can be completely disassembled and disposed of.

 

Disconnect the product completely from the power supply.

 

Dispose of the components properly according to the material groups.

 

Comply with the locally applicable environmental and disposal regulations.

Zimmer GmbH • Im Salmenkopf 5 • 

 77866 Rheinau, Germany • 

 +49 7844 9138 0 • www.zimmer-group.com

INSTALLATION AND OPERATING INSTRUCTIONS: 

SWM1000

DDOC00964 / a

EN / 2023-01-13

Содержание SWM1000 Series


















Отзывы: