Zimmer Match LWR50L-21 Series Скачать руководство пользователя

Страница: 38 / 53

11.7.1 DeviceMode 10

►

Assign "DeviceMode 10.

►

Transmit this value to the product with a handshake.

• The motor can be switched on or off.

WARNING

Risk of injury due to uncontrolled movements

Transmitting the value might cause the product to move.

►

Always keep an adequate safety distance.

►

Do not reach into the operational range of the product.

The gripper jaws move to the outside at low speed until they encounter the internal mechanical end stops.

If the gripper jaws encounter resistance, they stop at this spot.

In the process, the ActualPosition is referenced to the value of 0.

The motor is switched on.

11.7.2 DeviceMode 14

►

Assign DeviceMode 14.

►

Transmit this value to the product with a handshake.

• The motor can be switched on or off.

WARNING

Risk of injury due to uncontrolled movements

Transmitting the value might cause the product to move.

►

Always keep an adequate safety distance.

►

Do not reach into the operational range of the product.

The gripper jaws move to the inside at low speed until they encounter the internal mechanical end stops.

If the gripper jaws encounter resistance, they stop at this spot.

In the process, the ActualPosition is referenced to the maximum jaw stroke of the product.

The motor is switched on.

INSTALLATION AND OPERATING INSTRUCTIONS:

LWR50L-21/LWR50L-22

DDOC01071 / b

EN / 2021-11-25

Zimmer GmbH • Im Salmenkopf 5 •



77866 Rheinau, Germany •



+49 7844 9138 0 • www.zimmer-group.com

Содержание Match LWR50L-21 Series






















































Результаты поиска

Содержание Match LWR50L-21 Series

Отзывы:

Похожие инструкции для Match LWR50L-21 Series

Бренды по названию

Популярные бренды

Zimmer Match LWR50L-21 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Match LWR50L-21 Series

Отзывы:

Похожие инструкции для Match LWR50L-21 Series

Бренды по названию

Популярные бренды