background image

Z8FMC16100 Series Motor Control Development Kit

Quick Start Guide

QS005406-0111

Page 15 of 15

DO NOT USE THIS PRODUCT IN LIFE SUPPORT SYSTEMS.

LIFE SUPPORT POLICY

ZILOG’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL 
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE 
EXPRESS PRIOR WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL 
COUNSEL OF ZILOG CORPORATION. 

As used herein

Life support devices or systems are devices which (a) are intended for surgical implant 
into the body, or (b) support or sustain life and whose failure to perform when properly 
used in accordance with instructions for use provided in the labeling can be reasonably 
expected to result in a significant injury to the user. A critical component is any 
component in a life support device or system whose failure to perform can be reasonably 
expected to cause the failure of the life support device or system or to affect its safety or 
effectiveness.

Document Disclaimer

©2011 Zilog, Inc. All rights reserved. Information in this publication concerning the 
devices, applications, or technology described is intended to suggest possible uses and 
may be superseded. ZILOG, INC. DOES NOT ASSUME LIABILITY FOR OR 
PROVIDE A REPRESENTATION OF ACCURACY OF THE INFORMATION, 
DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZILOG ALSO 
D O E S   N O T   A S S U M E   L I A B I L I T Y   F O R   I N T E L L E C T U A L   P R O P E RT Y  
INFRINGEMENT RELATED IN ANY MANNER TO USE OF INFORMATION, 
DEVICES, OR TECHNOLOGY DESCRIBED HEREIN OR OTHERWISE. The 
information contained within this document has been verified according to the general 
principles of electrical and mechanical engineering.
Z8, Z8 Encore!, Z8 Encore! XP, Z8 Encore! MC, Crimzon, eZ80, and ZNEO are 
trademarks or registered trademarks of Zilog, Inc. All other product or service names are 
the property of their respective owners. 

Caution:

Содержание Z8FMC16100 Series
















Отзывы: