ZIEHL-ABEGG AM-PREMIUM Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 90

ZIEHL-ABEGG AM-PREMIUM Скачать руководство пользователя страница 6

Danger due to electric current

•

It is generally forbidden to carry out work on electrical live parts. Protection class of the device
when open is IP00! It is possible to touch hazardous voltages directly.

•

The 5 electrical safety rules must be observed!

•

The safe isolation from the supply must be checked using a

two-pole

voltage detector.

•

Even after disconnecting the mains voltage, life-threatening charges can appear between the
protective ground

“

PE

”

and the mains connection.

Waiting period at least 3 minutes!

Opening the device in which the module is to be installed (fan, inverter) is only allowed when the
mains power is switched off and after waiting at least three minutes.
Through use of capacitors, danger of death exists even after switching off the device through directly
touching the energized parts or due to parts that have become energized due to faults.

3

General description

3.1

Operational area

The add-on module can only be used together with compatible ZIEHL-ABEGG devices.

Note: The AM-PREMIUM-W module is intended exclusively for integration and utilisation in host
devices (fans and converters) from ZIEHL-ABEGG.

3.2

Function

By plugging on the

“

AM-PREMIUM

”

module, the fan / frequency inverter becomes a full universal

controller.
The module has two analog inputs (e.g. for sensors), one analog output and a MODBUS interface.
Type

“

AM-PREMIUM-W

”

additionally offers radio communication for parameterisation and data scan-

ning by the hand held terminal type A-G-247NW.

Type

Part-No.

Function

AM-PREMIUM

349046

Universal control module

AM-PREMIUM-W

349051

Universal control module
Communication by radio (wireless) to the hand held terminal A-G-247NW
additionally possible.

3.3

Transport

•

The device is packed ex factory to suit the transport method previously agreed.

•

Always use the original packaging materials when transporting the device.

•

Avoid shocks and impacts to the device during the transport.

•

During manual handling the human lifting and carrying restrictions must be observed and adhered
to.

3.4

Storage

•

The device must be stored in its original packaging in a dry and weather-proof room.

•

Avoid exposure to extreme heat and cold.

•

Avoid over-long storage periods (we recommend a maximum of one year).

3.5

Disposal / recycling

Disposal must be carried out professionally and in an environmentally friendly way in accordance with
the respective national legal stipulations.

"

Separate the materials by type and in an environmentally friendly way.

"

If necessary, commission a specialist company with the waste disposal.

Operating Instructions

AM-PREMIUM(-W)

–

model series

General description

L-BAL-E095-GB 1618 Index 006

Part.-No.

6/90

«
...
4
5
6
7
8
...
»

Содержание AM-PREMIUM



























































































Отзывы:

Нет отзывов