Zibro S 3025 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 40

Zibro S 3025 Скачать руководство пользователя страница 35

32

10.2 Diagnosis and Solution

10.2.1 E0 (EEPROM parameter error) error diagnosis and solution

10.2.2 E1 (indoor / outdoor units communication protection) error diagnosis and solution

10.2.3 E2 (zero-crossing signal error) diagnosis and solution

Disconnect the power supply, after 1 minute,
connect the power supply , turn on the unit with
remote controller

Does the unit work normally?

Check the wiring between
indoor and outdoor unit. Is
the connection of L, N, S and
GND good?
Is the GND connection on
outdoor PCB good?

NO

NO

Reconnect and retest again

Is the LED4(red) on outdoor
PCB bright and
LED1(yellow) blinking?

Replace outdoor e-box.

Yes

Yes

The power supply for
outdoor PCB is fail. Check
the wiring on outdoor PCB
comparing with wiring plate.
Is the connection good?

No

Correct the connection.

Yes

No

Replace indoor PCB
and repower on. Is
the failure cleared?

Is power supply and
connection of connectors
good?

Indoor PCB is defective. Replace
the indoor PCB.

Be sure the power supply is good
and correct the connection

NO

YES

Circuit or software error on indoor PCB

Replace indoor PCB

«
...
33
34
35
36
37
...
»

Содержание S 3025









































Отзывы:

Нет отзывов