15
alghamix II
en
the reference figures are present on pages 2, 3 and 4 of this manual and in the product Quick Guide
CHAPTER 6: INSTALLATION AND COMMISSIONING
6.1
WARNINGS AND PRECAUTIONS
before carrying out installation, make sure that all safety conditions
exist and follow the indications given below carefully.
for greater clarity, the numbers stated in the figures
positioned near to the paragraph boxes correspond to
the numbering of the data in Chapter 3, regarding the
“description of the machine”.
6.2
ACCEPTED ENVIRONMENTAL CONDITIONS
unless stated otherwise, at the time of ordering, it is intended
that the machine must be envisioned to function regularly in the
following environmental conditions:
Place of use ............................................................................. indoors
altitude ......................................................................... up to 2000 m
Working temperature ............................................ from 5°C to 40°C
Humidity .............................................................................. Max 80%
Conditions different to those prescribed can cause anomalies or
sudden breakdown.
lighting in the installation area of the machine must be sufficient
to guarantee good visibility in all points of the machine.
luminosity not less than 200 lux must be guaranteed. the lighting
must be uniform without reflections, which could dazzle the
operator.
the machine itself cannot cause explosions or fire: the
machine is not prepared and/or designed to operate in
environments with explosive atmosphere or with the
risk of fire.
the working area lighting plant is an important factor for
the safety of persons and the quality of work. in italy this
subject is governed by a Ministerial decree that clearly
determines the average level of prescribed lighting. in
other countries the regulations in force are valid regarding
accident-prevention and hygiene in the workplace.
6.3
SPACE NECESSARY FOR USE
the choice of the place and space required for installation is an
important factor for the quality of work and safety and for correct
maintenance activities.
this area must not only be spacious enough to allow for optimum
machine operation - also during cleaning and maintenance phases
- but must also be well lit, aired, not dusty and not exposed to
direct sunlight.
6.3.1 WorK toP
Fig. E:
the alghamix ii mixer has been designed to work on a
rigid worktop and parallel to the ground. suitable worktops
include service furniture (operator is standing) or modelling tables
(operator is sitting). all worktops must be checked for stability.
note also that the unit must be positioned so the connection plug
can be handled/manipulated with ease.
6.4
CONNECTION TO ENERGY SOURCES
the user must supply a power supply cable with relative socket
in the vicinity of the machine installation point and must prepare
a suitable isolating switch for the electric line upstream from
the socket, as well as sufficient means of protection against
overcurrents/indirect contacts.
the connection is made using the safety plug (16a, in compliance
with european standards), found at the end of the cable: it must
be inserted into the socket prepared by the user.
on connection check:
• that mains power supply voltage and frequency correspond to
those indicated on the identification plate (an incorrect power
supply voltage may damage the machine);
• that the power supply mains has a suitable earth connection.
do not tamper with the power supply cable and relative
plug. for replacement of the same due to damage and/or
wear, only contact authorised after-sales Centres.
an earth connection is mandatory. if an
extension must be used temporarily, it must
be in compliance with the standards in force
in the country of use.
5.2
PACKAGING AND UNPACKING
Fig. D:
all material is carefully controlled by the Manufacturer
before delivery.
on receiving the machine, make sure that it has not been damaged
during transport or that the packaging has not been tampered
with, resulting in missing parts.
should any damage or missing parts be noted, inform the dealer and
the Carrier immediately by forwarding photographic evidence.
the packaging, made up of a cardboard box with internal
protections, contains:
• the alghamix ii mixer;
• the material supplied (see par. 4.2.1);
• the use and Maintenance Manual.
it is recommended that you keep the original packaging
so that - if necessary - it can be re-used for transport
and handling the machine, thus preventing accidental
damage due to the use of unsuitable packaging (see
paragraph 5.3).
5.3
TRANSPORT AND HANDLING
if the alghamix ii mixer must be moved:
1. disconnect the machine from the electric power supply;
2. gather all accessories together (e.g. spatula and bowl), these
should be previously washed (see Chap. 8);
3. hold the bottom of the machine, always keeping it in a
horizontal position. a regarding this, pay attention to the weight
and clearance of the machine (see par. 4.2.3), in order to prevent
any type of damage occurring due to the failure of considering
these values.
both for transport and handling, it is prohibited to hold
the alghamix ii mixer by the bowl attachment, the bowl
itself or in any other way than that specified.
4. Pack the machine in the original packaging. if this is not possible,
take all necessary precautions to protect the machine from knocks
and drops, as the goods are transported at the owner’s risk.
failure to comply with the rules stated above relieve
the Manufacturer from any liability regarding machine
malfunctioning and consequently makes the warranty
null and void.
When shipping and/or delivering the machine to an
authorised after-sales Centre always enclose a copy of
the purchase document and a copy of the properly filled-
in identification form.
if the machine is transported by carrier, the Postal service
or rail, it is recommended to insure the shipment.
5.4
DISPOSAL / DISMANTLING
When disposing of the packaging material the user must follow the
regulations in force in the country of use relative to the following
materials:
• wood/paper: non-polluting materials, but must be re-cycled
correctly;
• polystyrene/plastic: pollutant material, do not burn (toxic fumes)
or dispose of in the environment. dispose of these materials in
compliance with the regulations in force in the country of use.
if the machine is to be dismantled, the operator must be in
charge of dismantling, elimination and re-cycling of the following
materials in compliance with the eeC directives and the laws in
force in the country of use:
• plastic parts; steel parts; glass parts; insulated electric cables;
rubber parts.
• there are no toxic or corrosive substances.
regarding the disposal of materials used for mixing, carefully
follow that specified on the labels of the individual products; in all
cases, respect the eeC directives and laws in force in the country
of use.
the product must not be disposed of as household
waste, but at the end of its life must be collected
separately in compliance with the 2002/96/Ce
directive.
