Zetor MAJOR HS Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 140

Zetor MAJOR HS Скачать руководство пользователя страница 96

Alternator maintenance

When washing and cleaning tractor protect alternator prior to penetration of water or oil!

You must not disconnect alternator from accumulator during operation!

Alternator must not ever be put in operation with a disconnected conductor from of clamp '+B' and

connected clamp '+D'. Such condition when increasing the revolutions may cause an exceptionally

high alternator voltage which would damage semiconductors!

Never short circuit any clamp of alternator in operation!

Alternator must not be over activated. There is a risk of semiconductors damage with this

intervention!

Mind the perfect electrical joint on connecting clamps and on perfect alternator grounding!

Alternator must not be overpoled not even for a short time!

Fuse box

MHS16N108

The fuses No 1 - 16 are located in the fuse box on the right side of the steering column (A).
The fuses No 17 - 19 are located in the fuse box on the left side of the steering column (B).
The fuses are accessible after the cover of the fuse boxes is removed. The fuses are knife type and during
their replacement it is necessary to adhere to the prescribed value of the fuse. If interrupted repeatedly,
search the nearest service.

The glow fuse (C) is accessible when the cover (1) is removed. It is a strip type with the size of 80A.
During replacement of fuses it is necessary to adhere to the prescribed value of the fuse. If interrupted
repeatedly, search for the nearest service.

ELECTRIC INSTALLATION

95

«
...
94
95
96
97
98
...
»

Содержание MAJOR HS













































































































































Отзывы:

Нет отзывов