manualshive.com logo in svg

Zetor MAJOR HS, Руководство оператора

Поделиться
Скачать
Zetor MAJOR HS Скачать руководство пользователя страница 125

 

Bleeding of tractor brake system 

 

Only hydraulic mineral oil Titan ZH LHM PLUS can be used in the brake system. 

 
1. Deaeration of main brake cylinders 

2. Deaeration of the main brake valve for trailers 

E758

 

 

Should be performed under operating pressure of the air in the system 600 ± 20 kPa with the following 
procedure: 
1. Add the missing amount of the brake fluid in the equalizing vessel to the max. amount. 
2. Remove the caps from deaeration screws (2) of the main control valve of the trailer (1) located on the right 
side of the tractor between the battery and rear half-axle. 
3. Install hoses on the screws and immerse their other ends to the bottom of the transparent vessel (3) partly 
filled with the brake fluid. Place the vessel at least 300 mm above the deaeration screws. The screws must 
be permanently under pressure to prevent air penetration through their threads. 
4. Release the deaeration screws by 1/4 revolution max. 
5. Press down the pedal fully and tighten the deaeration screw. 
6. Release the brake pedal and repeat the procedure until no air bubbles come out of hose. 

Perform deaeration of the brake system of the tractor 
always in the following order: 
 
1. Main brake cylinders 
2. Pressure air brake system for trailers 
3. Foot brakes of rear wheels 
 
Perform deaeration of main brake cylinders, pressure air 
brake systems for trailers and foot brakes of rear wheels 
with connected brake pedals. 
During deaeration observe the amount of liquid in the 
balancing tank to avoid intake of air. 
After two years replacement of the brake fluid in the whole 
brake circuit must be performed. 

MHS16N050

 

 

Use the following procedure: 
1. Add the missing amount of the brake fluid in the 
equalizing vessel to the max. amount. 
2. Remove the caps from deaeration screws (2) of main 
brake cylinders (1) located on the right side of the tractor 
between the cabin and the engine. 
3. Install hoses on the screws and immerse their other 
ends to the bottom of the transparent vessel (3) partly 
filled with the brake fluid. Place the vessel at least 300 mm 
above the deaeration screws. The screws must be 
permanently under pressure to prevent air penetration 
through their threads. 
4. Release the deaeration screws by 1/4 revolution max. 
5. Press down the pedals fully and tighten the deaeration 
screws. 
6. Release the brake pedals and repeat the procedure 
until no air bubbles come out of hose. 
 

MHS16N075

 

 

ADJUSTMENT

124

Содержание MAJOR HS













































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды