manualshive.com logo in svg

Zetor MAJOR HS, Руководство оператора

Поделиться
Скачать
Zetor MAJOR HS Скачать руководство пользователя страница 48

Before a drive with the new tractor get to know how to shift gears and try individual positions 

of the shifting lever when the engine is stopped.
During normal operation and before you set up, make sure that the technical condition ensures safe 
operation of the tractor.

Before you start the engine

Starting the engine

MHS16N021

1. Insert the key in the switch box - position '0'.
2. Push down the clutch pedal.
3. Move the reversing lever to the neutral position.
4. Move the main gear shift lever to the neutral position - the start circuit breaker is switched.
5. Set the fuel manual regulation lever to the idling position.
6. Switch the key of the switch box from the position '0' to the position 'I'. The thermostat glowing signal lamp 
is activated. Wait until the glowing signal lamp goes out (the time depends on the temperature of the cooling 
liquid).
7. Immediately after the lamp goes out (5 s max.) turn the key from 'I' position to 'II' position (start).
8. After starting the engine, immediately release the key and it is automatically returned to the position 'I'. 

Do not perform starting for a longer period than 15 s.

Before you start the engine, make sure that: 

1. 

tractor is properly braked 

2. 

PTO shaft drive engagement lever is in neutral 

position 

3. 

the main gear shifting lever is in neutral position 

Notes :

 If the clutch pedal is not depressed, it is not 

possible to start the engine - switch for securing start is 
not switched.

MHS16N020

DRIVING OPERATION

47

Содержание MAJOR HS













































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды