background image

Setting up the Desk for
Programming

1.

If the desk is in PRESET or SUPER
USER Mode, press and hold the
MODE button for 1 second to enter
PROGRAM Mode. If the desk is in
RUN Mode, press the MODE button
to enter PROGRAM Mode.

2.

Ensure that Blackout is not active 
(light in the BLACKOUT button is off)

3.

Select WIDE, if required.

4.

Set all the PRESET faders to zero.

5.

Set the A MASTER, B MASTER and
GRAND MASTER to full.

Selecting a Scene Memory

1.

Use the MEMORY PAGE button to
select the required page. The
CHANNEL FLASH buttons below the
PRESET A faders now represent
memories 1 -12 (1 - 24); the
CHANNEL FLASH buttons below the
PRESET B faders represent
memories 13 - 24 (25 - 48). The

yellow lights are illuminated in the
CHANNEL FLASH buttons if the
memory is programmed.

2.

Press a CHANNEL FLASH button to
select the corresponding memory.
The light in the button flashes to
indicate that the memory has been
selected. The lights in all the other
CHANNEL FLASH buttons go out.
The output levels are determined by
the positions of the PRESET faders.

Programming a Scene Memory

1. Select a scene memory to be

programmed as described above.

2. Use the PRESET A and PRESET B

faders to set the required output
levels. The outputs appear live.

3. Press the PROGRAM button. The

output levels are stored in the
selected memory. The yellow light in
the CHANNEL FLASH button
changes from flashing to on, to show
that the memory is now programmed.
The lights in the other CHANNEL
FLASH buttons come back on if the

corresponding memories are
programmed.

Overwriting a Scene Memory

1. Select a programmed scene memory

as described earlier.

2. Use the PRESET A and PRESET B

faders to set the required output
levels. The outputs appear live.

3. Press the PROGRAM button. The

original contents of the memory are
overwritten with the current output
levels.

Page 20

 

ELARA 73-710-00 Issue 3

Program Mode

Содержание Zero88









































Отзывы: