background image

Two Preset Operation

The PRESET A and PRESET B faders,
the A MASTER and B MASTER and the

GRAND MASTER are used to control the
output levels from the desk. 

The CROSSFADE control is used to

determine the crossfade time between the 
preset masters.

Setting up for Two Preset Operation

1.

If the desk is not already in PRESET
Mode, press and hold the MODE
button for 1 second. The PRESET
light above the MODE button will
come on.

2.

Ensure WIDE is not active and the
CROSSFADE control is set to
Manual.

To Output a Scene from Preset A

1.

Set the required levels for each
channel on the PRESET A faders.

2.

Set the A MASTER to full and the 
B MASTER to zero. The scene set up 
on PRESET A is output live.

To Output a Scene from Preset B

1.

Set the required levels for each
channel on the PRESET B faders.

2.

Set the A MASTER to zero and the B
MASTER to full. The scene set up on
PRESET B is output live.

Manual Fading between Scenes

1. Ensure that the CROSSFADE control

is set to Manual.

2. Set up a scene using the PRESET A

faders.

3. Set up a different scene on the

PRESET B faders.

4. Set the A MASTER to full, and the 

B MASTER to zero. The scene set on 
the PRESET A faders will be output.

5. To crossfade to the scene set up on

PRESET B, simultaneously move the
A MASTER to zero and the B
MASTER to full.  The operator has
direct control over the speed of the

scene change. As the master faders
are moved in tandem the scene set
up on PRESET B will fade in and the
scene set on PRESET A will fade out. 
The crossfade is dipless

6. A new scene can then be set up on

PRESET A without affecting the
outputs.

7. To crossfade to the new scene on

PRESET A, simultaneously move the
A MASTER to full and the B MASTER 
to zero. 

8. As the master faders are moved in

tandem the scene set up on PRESET 
B will fade out and the scene set on

PRESET A will fade in. The crossfade 
is dipless.

Page 12

 

ELARA 73-710-00 Issue 3

Preset Mode

Содержание Zero88









































Отзывы: