Zepro ZHD 2500-130 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 68

Zepro ZHD 2500-130 Скачать руководство пользователя страница 29

ZHD 2500-130/150

Installation

29

www.zepro.com

Lock screws, 3 pcs.

Out

In

Image 44. Adjusting the fit with the vehicle body

Image 45. Adjusting the tilt angle

4. Turn the adjusting collar so that the platform just

meets the seal on the vehicle body. Image 44.

5. Loosen the three lock screws on the other tilt

cylinder. Image 45.

6. Turn the adjusting collar so that the tilt cylinder

aligns with the attachment on the platform. See

Image 45.

The max. length of both cylinders must be

adjusted equally to avoid unwanted breakout

forces.

m

WARNING!

7. Fit the other tilting cylinder to the platform

mounting. Use the supplied shaft and support

wheel.

Make sure the cylinder is installed with the

grease nipple facing up.

NOTE.

8. Tighten the bolts using a torque wrench.

Tightening torque: 80 Nm.

9. Adjust the two cylinders alternately so that the

platform meets the vehicle body. See Image 44 (B).

Image 46. Fitting the tilt cylinder to the platform

«
...
27
28
29
30
31
...
»

Содержание ZHD 2500-130





































































Отзывы:

Нет отзывов