manualshive.com logo in svg

Zepro ZHD 2500-130, Руководство по установке, Страница: 17 / 68

Поделиться
Скачать
Zepro ZHD 2500-130 Скачать руководство пользователя страница 17

ZHD 2500-130/150

Installation 

17

www.zepro.com

10.  When installing on a frame without pre-drilled holes, 

install first with a screw in the brackets’ slot-shaped 

holes. On the vehicle chassis, mark the middle of the 

brackets’  slot-shaped  holes  and  then  drill  Ø14  mm 

holes in the frame, see Image 16.

11.  Bolt the brackets securely on the outside of the vehicle 

chassis. Use M14x45 bolts and install the associated 

washer and nut on the inside of the vehicle chassis. 

Install the bolts but do not tighten.

12. 

Check and perform fine adjustment regarding the position 

of the lift. Then tighten the bolts with a torque wrench. 

Tightening torque: 120 Nm.

13. Using a torque wrench, tighten the nuts holding the 

U-profiles. 

Tightening torque: 280 Nm.

14.  Drill holes in the vehicle chassis for mounting bolts, 

Ø14  mm.  Drill  in  the  outer  holes  of  each  bracket. 

Use M14x45 bolts and install the associated 

washer and nut on the inside of the vehicle chassis. 

Installation must be performed with at least 8 

bolts in the outer holes. The bolt that was installed 

initially in the slot-shaped hole may not be included 

in  this  figure.  If  necessary,  this  bolt  can  now  be 

moved to one of the outer holes, see illustration. 

Then tighten the bolts with a torque wrench. 

Tightening torque: 120 Nm.

 

Welding is not permitted on the chassis brackets.
Do not move the lift all the way to the armstops or 

with the platform fitted before all the bolts are fully 

tightened against the chassis.
Do not place the lift under load until:
·  the correct number of bolts have been installed 

and torque-tightened.

·  the vehicle body is installed to reinforce the truck 

chassis.

NOTE.

 

15. Remove the mounting jig.

Image 15.  The chassis bracket requires 

at least 35 mm clearance between ve-

hicle chassis and support frame

Image 16.  Install the chassis bracket 

with at least 8 M14x45 10.9 bolts

When installing on chassis with pre-drilled holes, 

go directly to point 16.

35 mm

35 mm

Min. 260

Min. 20

Min. 202.5

Min. 20

Min. D

D

Min. 8 pcs.

M14x45 10.9

120 Nm

New hole

Содержание ZHD 2500-130





































































Отзывы:

Нет отзывов