background image

2

SAFETY, INSTALLATION, AND OPERATION

ELECTRIC DRIVEN COLD WATER CLEANER

1.  Before operating this machine, read and  observe

all safety, unpacking, and operating instructions.
Failure to comply with these  instructions could
create a hazardous  situation.

2.  The operator of this equipment should not operate

this equipment when fatigued or under influence of
alcohol or drugs.

3.  The operator of this equipment should be

thoroughly  familiar  with its operation and trained
in the job to be accomplished.

4.  The operator of this equipment should wear

protective face shields and other protective
clothing as required for safe operation.

5.  Keep all protective covers and shields in place.

Operating this machine with moving parts could
allow operator or bystander serious injury or even
death.

6.  Do not operate the machine if any mechanicalfailure

is noted or suspected. Keep all shields in place.

7.   Always point the gun assembly in a safe direction

and do not direct spray on the cleaner.

GENERAL SAEFTY

Supersedes 08-19-05 Z08-00481

 

   05-18-06   Z08-00481

Read and understand this “OPERATOR’S
MANUAL” and “LABELS
ON THE MACHINE” before
starting.

MACHINE UNPACKING

ALL CLEANERS ARE CAREFULLY INSPECTED AND
CARTONED TO PROTECT AGAINST SHIPPING
DAMAGE.  IF THERE IS DAMAGE OR MISSING PARTS,
THE TRANSPORTATION COMPANY AGENT SHOULD
MAKE A NOTATION TO THAT EFFECT ON THE BILL.
REFER TO THE PARTS LIST IN THIS MANUAL AND
ADVISE WHAT PARTS ARE MISSING OR DAMAGED.
IF AVAILABLE, GIVE THE INVOICE NUMBER ON ALL
ORDER BILLS.  THIS PROCEDURE WILL ENABLE
NEEDED PARTS TO BE SHIPPED QUICKLY.

READ ALL

 Installation, Operation, and Maintenance

instructions before operating the machine.

NOTE: 

Refer to CLEANER MODEL for 

SERIAL NUMBER

location.

NOTE:

 Dimensions are in inches unless otherwise note.

The safety alert symbol.

This symbol is used

to identify safety information about hazards that can
result in personal injury.
A signal word (DANGER, WARNING, or CAUTION) is used
with the alert symbol to indicate the likelihood and the
potential severity of injury.  In addition, a hazard symbol
may be used to represent the type of hazard

   

DANGER 

indicates a hazard which, if not avoided,

will result in death or serious injury.

   

WARNING

 indicates a hazard which, if not avoided,

could result in death or serious injury.

   

CAUTION 

indicates a hazard which, if not avoided,

might result in minor or moderate injury.

       

CAUTION

, when used 

without

 the alert symbol,

indicates a situation that 

could result in damage to

the equipment.

IMPORTANT SAFETY

INSTRUCTIONS

WARNING:

  

RISK OF INJECTION OR

SEVERE INJURY.  KEEP CLEAR OF
NOZZLE. DO NOT DIRECT DISCHARGE
STREAM AT PERSONS.  THIS EQUIPMENT
IS TO BE USED ONLY BY TRAINED
OPERATORS.

AVERTISSEMENT:

RISQUE D’INJECTION ET

DE BLESSURES GRAVES.  SE TENIR À
L’ÉCART DU JET.  NE PAS DIRIGER LE JET
DE SOTIE VERS D’AUTRES PERSONNES
CONFIER L’UTILISATION LE JET DE SOTIE
VERS D’AUTRES PERSONNES. CONFIER
L’UTILISATION DE CE MATÉRIEL À UN
OPÉRATEUR QUALIFIÉ.

ADVERTENCIA:

RIESGO DE LA INYECCIÓN

O SEVERO LESIÓN. CLARO DE LA
SUBSISTENCIA DEL INYECTOR. NO DIRIJA
LA CORRIENTE DE LA DESCARGA EN LAS
PERSONAS. ESTO EL EQUIPO DEBE SER
UTILIZADO SOLAMENTE POR LOS
OPERADORESENTRENADOS.

Содержание 212 CD

































Отзывы: