Zener SMARTSTART 6000 Series, Руководство пользователя

Страница: 38 / 43

Appendix A
Indicative parameters for different load types
Technical Manual: Smartstart
®
6000 IMI0042 rev D
Page 35
1. Pump (3 wire/Bypass with No Soft Stop)
Factory defaults are intended for general
pumping/fan application with no Soft Stop. Enter
motor parameters as per motor nameplate.
2. Submersible Pump
(3 wire/Bypass with No Soft Stop)
Factory defaults are intended for general pumping
application with no Soft Stop. The acceleration
time needs to be reduced to 3secs or as per
pump/motor manufacturers recommendations.
Enter motor parameters as per motor nameplate.
Ref Page Parameter Setting (factory Default)
C11 17 Accel time 3sec (10s)
M01 17 Motor Amps ‘Namplate Motor FLC’
M02 17 Motor Volts ‘Namplate Motor Volts’
M03 17 Motor PF ‘Namplate Motor PF’
3. Pump :(3 wire/Bypass with Soft Stop)
Factory defaults are intended for general pumping
application with no Soft Stop. Enter motor
parameters as per motor nameplate. Adjust the
‘Release Torque’ and ‘Decel time’ to achieve the
required soft stop.
Ref Page Parameter Setting (factory Default)
C21 18 Decel time *15sec (0s)
C22 18 Release Torque *2% (2%)
M01 17 Motor Amps ‘Namplate Motor FLC’
M02 17 Motor Volts ‘Namplate Motor Volts’
M03 17 Motor PF ‘Namplate Motor PF’
4. Fan :(3 wire/Bypass)
Factory defaults are intended for general pumping
application which is similar to that required for a
fan. However, the Accel time may need to be
increased to allow for longer ramp times of high
inertia fans. The Motor Overload Class may also
need to be increased with the extended ramp of
high inertia fans. Enter motor parameters as per
motor nameplate.
Ref Page Parameter Setting (factory Default)
C11 17 Accel time 15+ (10s)
P01 18 Motor Overload Class 10 /Class 20 (10)
M01 17 Motor Amps ‘Namplate Motor FLC’
M02 17 Motor Volts ‘Namplate Motor Volts’
M03 17 Motor PF ‘Namplate Motor PF’
5. Conveyor: (3 wire/Bypass)
Factory defaults are preset for a variable torque
load. The Torque settings will need to be adjusted
for a constant torque type load. Enter motor
parameters as per motor nameplate.
Ref Page Parameter Setting (factory Default)
C12 17 Start Torque 150% (30%)
C13 18 Final Torque 150% (130%)
A21 23 Accel profile Linear (Squared)
P01 18 Motor Overload Class 20 (10)
M01 17 Motor Amps ‘Namplate Motor FLC’
M02 17 Motor Volts ‘Namplate Motor Volts’
M03 17 Motor PF ‘Namplate Motor PF’
6. Compressor: (3 wire/Bypass)
Factory defaults are preset for a variable torque
load. The Torque settings will need to be adjusted
for a constant torque type load. Enter motor
parameters as per motor nameplate
.
Ref Page Parameter Setting (factory Default)
C12 17 Start Torque 60% (30%)
C13 18 Final Torque 130% (130%)
A21 23 Accel profile Linear (Squared)
P01 18 Motor Overload Class 20 (10)
M01 17 Motor Amps ‘Namplate Motor FLC’
M02 17 Motor Volts ‘Namplate Motor Volts’
M03 17 Motor PF ‘Namplate Motor PF’
7. Suggested Protection Settings
Below are suggested settings to provide additional
protection of the motor and load. These are
general settings and should be further tuned to
suit the application and load conditions.
Ref Page Parameter Setting (factory Default)
P01 18 Motor Overload Class 10a/10/20 (10)
P02 18 Motor O/Temp Thermistor (Disabled)
P03 18 Phase Rotation 1-2-3 (Disabled)
P10 19 Accel O/Time Trip / 5s (Disabled)
P20 19 Volt Imbal. Trip / 25% / 5s (Default)
P30 19 Current Imbal. Trip / 25% / 10s (Default)
P41 20 Under Current Trip / 50% / 10s (Disabled)
P70 21 Over Torque Trip / 110% / 10 s (Disabled)