99
Spray arms
Check whether or not the holes
for the upper and lower spray
arms are clogged. If there is any
clogging, remove the spray arms
and clean them under water.
You can remove the lower spray
arm by pulling it upwards, while
the upper spray arm nut can be
removed by turning the nut to the
left.
Be sure that the nut is perfectly
tightened when refitting the upper
spray arm.
Failure codes and what to do in case of failure
ERROR CODE ERROR DESCRIPTION
CONTROL
F5
Inadequate water supply.
Make sure the water input tap is totally open and that there is no water cut.
•
Close the water input tap, separate the water input hose from the tap and clean the filter at the
•
connection end of the hose.
Restart your machine, contact the service if the error resumes.
•
F3
Error of continuous water input.
Close the tap.
•
Contact the service.
•
F2
The waste water in the machine cannot be discharged.
Water discharge hose is clogged.
•
The filters of your machine might be clogged.
•
Power off-on your machine and activate the program cancellation command.
•
If the error continues, contact the service.
•
F8
Heater error.
Contact the service.
F1
Alarm is active against water overflow.
Power off your machine and close the tap.
•
Contact the service.
•
FE
Faulty electronic card.
Contact the service.
F7
Overheating error (temperature in the machine is too high). Contact the service.
F9
Divisor position error.
Contact the service.
F6
Faulty heater sensor.
Contact the service.
Hose filter
Water is prevented by the inlet hose filter so as to avoid any damage to your machine
because of any contamination (sand, clay, rust etc.) that might be occasionally carried in
through the mains water supply or the indoor plumbing, and to forestall such complaints
as yellowing and formation of deposits after washing. Check the filter and the hose from
time to time and clean them if necessary. To clean the filter, first turn off your tap and then
remove the hose. After removing the filter from the hose, clean it under the tap. Insert the
cleaned filter back into its place inside the hose. Refit the hose.
If the programme won’t start
Check if the plug is connected.
●
Check your indoor fuses.
●
Be sure that the water inlet tap is turned on.
●
Be sure that you have closed the machine door.
●
Be sure that you switched off the machine by pressing the Power On/Off button.
●
Be sure that the water inlet filter and the machine filters are not clogged.
●
If detergent residues are left in the detergent compartment
Detergent has been added when the detergent compartment was wet.
●
If water is left inside the machine at the end of the programme
The water drain hose is clogged or twisted.
●
The filters are clogged.
●
The programme is not finished yet.
●
If the machine stops during a wash operation
Power failure.
●
Water inlet failure.
●
Program can be on standby mode.
●
If shaking and hitting noises are heard during a wash operation
Dishes placed incorrectly.
●
Spray arm hitting the dishes.
●
If there are partial food wastes left on the dishes
Dishes placed incorrectly into the machine, sprayed water did not reach related places.
●
Basket overly loaded.
●
Dishes leaning against one another.
●
Very small amount of detergent added.
●
An unsuitable, rather weak wash programme selected.
●
Spray arm clogged with food wastes.
●
Filters clogged.
●
Filters incorrectly fitted.
●
Water drain pump clogged
●
If there are whitish stains on the dishes
A very small amount of detergent is being used.
●
Rinse aid dosage setting at a very low level.
●
No special salt is being used despite the high degree of water hardness.
●
Water softener system setting is at a very low level.
●
Salt compartment cap not closed well.
●
A detergent without phospate used; try one that contains phosphate.
●
If the dishes won’t dry up
A programme without a dry operation selected.
●
Rinse aid dosage set too low
●
Dishes unloaded too fast.
●
If there are rust stains on the dishes
Stainless-steel quality of the dishes washed is insufficient.
●
High rate of salt in the wash water.
●
Salt compartment cap not closed well.
●
Too much salt spilt into the sides and into the machine while filling it with salt.
●
Unhealthy mains grounding
●
Door is not opened/closed properly
Not proper weight wooden part inserted on the door. (Follow the weight given in the
●
Assembly manuel)
The tensile of the door spring not adjusted properly. Adjust it according to the Assembly
●
manuel.
Call an authorised service if the problem still persists after the controls or in case of
any malfunction not described above.
Practical and useful information
1
Whenever you will not be operating your machine
Unplug the machine and then turn the water off.
●
Leave the door slightly ajar in order to prevent the formation of unpleasant smells.
●
Keep the machine interior clean.
●