93
Set the water softener.
●
Add 2 kg salt into the salt compartment and fill with water up to a level at which it will
●
almost overflow.
Fill the rinse aid compartment.
●
Preparing the machine for use
The importance of water decalcification
For a good washing function, the dishwasher needs soft, i.e. less calcareous water.
Otherwise, white lime residues will remain on the dishes and the interior equipment. This
will negatively affect your machine’s washing, drying and shining performance. When
water flows through the softener system, the ions forming the hardness are removed from
the water and the water reaches the softness required to obtain the best washing result.
Depending on the level of hardness of the inflowing water, these ions that harden the
water accumulate rapidly inside the softener system. Therefore, the softener system has
to be refreshed so that it operates with the same performance also during the next wash.
For this purpose, dishwasher salt is used.
Filling with salt
Use softener salt specifically produced for use in dishwashers. To put softener salt, first
remove the lower basket and then open the salt compartment cap by turning it counter
clockwise
1
,
2
. At first fill the compartment with 2kg salt and water
3
at overflowing
level If available,using the funnel
4
provided will make filling easier, refit the cap and
close it.If the salt warning lamp on the control panel becomes on fill the salt compartment
with salt again
NOTE:
Fill the salt compartment with water at first use only.
If you put a tablet into the salt compartment, do not fill the compartment completely. We
recommend that you use small-grained or powder softener salt.
Do not put table salt into your machine. Otherwise, the function of the softener compartment
may decrease over time. When you start your dishwasher, the salt compartment gets filled
with water. Therefore, put the softener salt prior to starting your machine.
This way, overflowing salt gets immediately cleaned up through the wash operation. If you
are not going to wash any dishes immediately after putting salt, then run a short washing
program with an empty machine in order to avoid any damage (to prevent corrosion) to
your machine due to the salt overflow while filling in the salt container.
Testing strip
The washing effectiveness of your machine depends on the softness of the tap water. For
this reason, your machine is equipped with a system that reduces the hardness in mains
water supply. The washing effectiveness will increase when the system is correctly set. To
find out the water hardness level of water in your area, contact your local water board or
determine water hardness level by using the test strip(if available).
Water connection
Be sure that the indoor plumbing is suitable for installing a dishwasher. Also, we
recommend that you fit a filter at the entrance of your place or apartment so as to avoid
any damage to your machine because of any contamination (sand, clay, rust etc.) that
might be occasionally carried in through the mains water supply or the indoor plumbing,
and to forestall such complaints as yellowing and formation of deposits after washing.
Water inlet hose
Do not use the water inlet hose of your old machine, if any. Use
the new water inlet hose supplied with your machine instead.
If you are going to connect a new or long-unused water inlet
hose to your machine, run water through it for a while before
making the connection. Connect the water inlet hose directly
to the water inlet tap. The pressure supplied by the tap should
be at a minimum of 0.03 Mpa and and at a maximum of 1 Mpa.
If the water pressure is above 1 Mpa, a pressure-relief valve
should be fitted inbetween.
After the connections are made, the tap should be turned on
fully and checked for water tightness.
For the safety of your machine, make sure to always turn off the water inlet tap after each
wash programme is finished.
NOTE: Aquastop water spout is used in
some models. In case of using Aquastop,
a dangerous tension exists. Do not cut
Aquastop water spout. Do not let it get
folded or twisted.
Water outlet hose
The water drain hose can be connected
either directly to the water drain hole or to
the sink outlet spigot. Using a special bent
pipe (if available), the water can be drained
directly into the sink via hooking the bent
pipe over the edge of the sink.
This connection should be at a minimum
of 50 cm and and at a maximum of 110 cm
from the floor plane.
WARNING: When a drain hose longer
than 4 m is used, the dishes might
remain dirty. In that case, our company
will not accept responsibility.
Electrical connection
The earthed plug of your machine should be connected to an earthed outlet supplied
●
by suitable voltage and current. If there is no earthing installation, have a competent
electrician carry out an earthing installation. In case of usage without earthing installed,
our company will not be responsible for any loss of usage that might occur.
The indoor fuse current value should be 10-16 A.
●
Your machine is set according to 220-240 V. If the mains voltage in your location
●
is 110 V, connect a transformer of 110/220 V and 3000 W inbetween. The machine
should not be plugged in during positioning.
Always use the coated plug supplied with your machine.
●
The machine’s electrical cable should be replaced by an authorised service or an
●
authorised electrician only. Failure to do so may lead to accidents.
In order not to cause an electric shock, do not unplug when your hands are wet.
●
For safety purposes, always make sure to disconnect the plug when a wash
●
programme is finished.
Running in low voltage will cause a decline in washing quality.
●
When disconnecting your machine from the mains supply, always pull from the plug.
●
Never pull the cord itself.
Prior to using the machine for the first time
Check whether the electricity and supply water specifications match the values
●
indicated by the installation instructions for the machine.
Remove all packaging materials inside the machine.
●
1
2
3
4