Zelmer ZVC542 Series, Руководство пользователя

Страница: 25 / 27

25
5 Release the front cover fastening (10) and open the
cover.
6 Remove the SAFBAG dust bag module from the vacuum
cleaner chamber (14) .
7
While holding the module, pull the frontal part of the bag
plate upwards and remove the bag. Close the SAFBAG bag
cap to close the full bag. Dispose of the bag.
8 Slide the plate of the new bag in the direction shown in
the picture. The end of the plate should lock in the socket.
The bag cap should be on top. The direction is shown by an
arrow placed on the bag.
●
Put the SAFBAG module together with the assembled
bag (14) into the vacuum cleaner container so that the
cogs of the SAFBAG module fit into the holes in the
container wall. Press and close the cover until you hear
the characteristic clicking sound – be careful not to catch
the bag.
Do not vacuum without SAFBAG bag module
installed. The lack of SAFBAG bag module
disables to slam the upper cover of vacuum
cleaner.
ZELMER vacuum cleaners are equipped with SAFBAG dust
bags in the amount indicated in the table. It is recommended
to replace the dust bag if:
a) the “Dust bag full” indicator light will come on,
b) the safety valve activates,
c) the vacuum cleaner operates poorly,
d) the dust bag is full.
Accessory holder
F
The accessory holder allows hanging accessories (suction
tube, small nozzle, small brush, crevice nozzle, combination
brush, turbobrush or parquet brush) for example in the
closet.
1 Join the holder elements.
2 Screw the holder (for example to the wall of the closet)
using the four provided screws.
3 Fit the accessories onto the holder as shown in the
picture.
Overheating protection
Models ZVC542HT, ZVC542HTUA, ZVC542ST, ZVC542STUA
have an overheating protection device. If will automatically
switch off power to the motor if it overheats. If this happens,
turn off the vacuum by pressing the ON/OFF button (8) . Allow
the vacuum cleaner to cool for approx. 40 min. and switch it
on again. If the vacuum cleaner does not start, return it to an
authorised service agent for repair.
Special accessories
The following special accessories may be purchased in retail
outlets:
Parquet brush “BNB” (18)
The parquet brush is used to clean and polish hard, scratch
sensitive surfaces such as wooden floors, floor panels,
parquet, marble, tiles, etc.
Delicate and soft natural bristles ensure maximum vacuum
effectiveness and protects against scratching the cleaned
surface.
Zelmer turbobrush (23)
May be used with all types of ZELMER vacuum cleaners.
Is used for an effective vacuuming of carpets and fitted
carpets. While using the turbobrush follow the instruction
manual.
The use of the turbobrush decidedly increases the
effectiveness of removing fibrous dirt such as: animal hair,
hair, threads etc. It is practically useful in households with
pets (cats, dogs), where removing the animal hair from the
carpets and floorings is very onerous.
End of operation cleaning
and maintenance
1
Switch off the vacuum cleaner by pressing the “on/off”
button (8) .
2 Unplug the appliance.
3
Wind the cord by pressing the cord rewind button (1) .
While doing this hold the cord to make sure it is not tangled
and the plug does not hit the vacuum cleaner housing.
4 Disconnect the telescopic tube from the nozzle or brush.
5 Disconnect the telescopic tube from the hose. In order to
remove the tube from the hose handle press the “A” locking
device and pull the tube in the direction of the arrow.
6 Press the two side buttons on the end of the hose and
remove the hose end from the inlet opening of the vacuum
cleaner.
7
The vacuum cleaner may be stored vertically or
horizontally. In order to do so, insert the fastening hook of
the combination brush to the combination brush fastener.
The hose may be attached to the vacuum cleaner, however
you have to make sure that it is not excessively bent during
storing.
8 If necessary wipe the housing and the dust bag container
with a damp cloth (it may be soaked with dishwashing liquid)
and dry it or wipe until dry.
Do not use abrasive detergents or solvents.
G