44
ZVC225-001_v03
PROBLEM
ACTION
The electrical installation
fuse went out.
Check if other appliances are not
plugged to the same electrical circuit
as the vacuum cleaner. If the fuse
goes out repeatedly, return the vacuum
cleaner to a service point.
The vacuum cleaner does
not operate; the housing or
the cord is damaged.
Return the vacuum cleaner to
a service point.
The suction power of the
vacuum cleaner is weak.
Replace the dust bag and the filters,
check the suction tube, the hose and
the nozzle – remove the cause of the
clogging.
Ecology – Environmental protection
Each user can contribute to protect the environment. It is
neither difficult nor expensive. In order to do so:
Return cardboard packages to recycling
points.
Throw polyethylene (PE) bags into appropriate
containers.
Return a worn out appliance to an appropriate
collecting point as the components of the
appliance may pose a threat to the environment.
Do not dispose the appliance with the municipal waste!
FOAM RUBBER COVER
1
Release the fastening of the upper cover
(6)
, and open it.
2
Remove the foam rubber cover
(12)
from the three
fastenings of the upper cover.
3
Replace the old foam rubber cover with a new one
(12)
in such a way that the three incisions on the foam rubber
cover find the three fastenings of the upper cover.
Always replace a damaged foam rubber cover
(12) with a brand new, original one.
4
Close the cover by pressing it, until you hear
a characteristic “click.”
After-work procedures, cleaning and
maintenance
1
Press the on/off switch
(4)
to stop the vacuum cleaner.
2
Remove the plug of the cord from the socket.
3
Wind the cord by pressing the cord winder button
(3)
.
Hold the cord when doing it to avoid tangling the cord up or
letting the plug hit the vacuum cleaner.
4
Disconnect the telescopic pipe from the nozzle or brush.
5
Disconnect the telescopic tube from the hose. In order to
remove the tube from the hose handle press the
“A”
locking
device and pull the tube in the direction of the arrow.
6
Press both of the side buttons situated on the end of the
hose, and remove the end of the hose from the inlet of the
vacuum cleaner.
7
The vacuum cleaner together with its attached
accessories may be stored in a vertical or horizontal position.
In order to this, place the hook of the nozzle brush into the
fastening for the nozzle brush. The hose may stay attached
to the vacuum cleaner as long as it is not bent too much
during storage.
8
If necessary, clean the casing and the chamber of the
vacuum cleaner with a damp cloth (it may be damped in
dishwashing liquid), dry it off, and wipe it dry.
Do not use any scrubbing agents or solvents.
Examples of problems while operating the
vacuum cleaner
PROBLEM
ACTION
A characteristic “fluttering”
of the vacuum cleaner is
heard.
• Check the dust bag and the
accessories, remove the cause of the
clogging or replace the dust bag with
a new one.
• Clean the vacuum cleaner chamber
and the filter.
The dust bag is damaged. Remove the dust bag and the filters.
E
F
The importer/manufacturer does not accept any liability for any
damages resulting from unintended use or improper handling.
The importer/manufacturer reserves his rights to modify the product
any time in order to adjust it to law regulations, norms, directives,
or due to construction, trade, aesthetic or other reasons, without
notifying in advance.
Содержание ZVC225SK
