Zelmer ZVC225SK, Руководство пользователя

Страница: 37 / 40

43
ZVC225-001_v03
device “A” and slide the tube into the hose handle so that
the locking device “A” is blocked in opening “B” .
3
Select the needed length of the telescopic suction pipe
by sliding the slider according to the arrow, and pulling out/in
the pipe.
4 Install a nozzle or a brush on the other end of the suction
pipe.
5
Use combination carpet & floor brush for vacuuming both
hard surfaces and carpets. To clean hard surfaces – wooden
floors, plastic floors, ceramic tiles etc. pull out the brush by
pressing the switch on the combination brush according
to the figure . Retract the brush when vacuuming
carpets (set the switch in “ ”).
6 Grab the plug of the cord (2) , and pull it out of the
vacuum cleaner.
When pulling out the cord pay attention to
the yellow band which marks the end of the
cord. Any attempts to unwind the cord further
(especially forcefully pulling on it) may lead to
damaging it.
7 Put the plug of the cord in an electric socket.
8 Press the on/off switch to start the vacuum cleaner.
9 The vacuum cleaner is equipped with an electronic
controller of suction power, which enables smooth regulation
of suction power of the vacuum cleaner. By turning the knob
(4) clockwise or counterclockwise you may increase or
decrease the suction power.
10 The vacuum cleaner is also equipped with a mechanic
suction power controller (8) , which is situated on the hose
handle. You may use it to slightly regulate the suction power
without the need to use the knob (4) .
(De)installing the SAFBAG-type bag
C
The vacuum cleaner is equipped with safety
valve located in chamber of dust container
(bag). It opens automatically in case of total
stopping of suction hose or total stopping of
equipment elements connected thereto, as well
as in case of overfill of dust bag. After opening
the valve one can hear characteristic “whirr”
sound inside the vacuum cleaner.
1 The vacuum cleaner is equipped with a full bag indicator
(5) . When the indicator light is on during work (a nozzle or
brush is over a cleaned surface), it means the bag needs
to be replaced. The full bag indicator (5) may also be on
when the suction hose or other accessories linked to it are
clogged up.
2 Press the on/off switch (4) to stop the vacuum cleaner.
Remove the plug of the cord from the socket.
3 Press both of the side buttons situated on the end of the
hose, and remove the end of the hose from the inlet of the
vacuum cleaner.
4 Release the fastening of the upper cover ( 6) , and open it.
5 Close the opening of the bag by means of a stopper.
6 Bend back the bag handle in the direction of the vacuum
cleaner handle (7) .
7 Grab the bag plate, pull it out of the handle, and then
remove the entire bag upwards.
8 Place the bag plate of a new bag into the guides of the
SAFBAG handle, and slide it to the limit. The direction in
which you should install the bag is marked by an arrow on
the bag.
9
Bend back the bag handle in the direction of the control
knob (4) .
10 Close the cover by pressing it, until you hear
a characteristic “click” – be careful not to trap the bag.
Do not start vacuuming without the SAFBAG-
type bag. No SAFBAG-type bag makes it
impossible to lock the upper cover of the
vacuum cleaner.
Zelmer vacuum cleaners are equipped with SAFBAG­type
bags in the amount given in the table. You have to replace
the bag, if:
a) the full bag indicator is on,
b) the vacuum cleaner works less efficiently,
c) the bag is full.
The number of SAFBAG bags set that can be purchased,
is placed on a sticker located in the vacuum chamber.
(De)installing the EPA inlet filter and the
foam rubber
Before replacing the EPA inlet filter and the foam rubber,
make sure the vacuum cleaner is turned off, and the plug of
the cord is out of the electrical socket.
INTAKE FILTER (EPA)
The vacuum cleaners are equipped with a EPA E11­class
inlet filter.
1 Release the fastening of the upper cover (6) , and open it.
2
Remove the SAFBAG­type bag (13) from the chamber of
the vacuum cleaner.
3 Pull out the EPA intake (11) from the guides situated at
the back wall of the chamber of the vacuum cleaner.
4 Put the new filter into the guides situated at the back wall
of the chamber of the vacuum cleaner.
Always replace a damaged EPA intake filter (11)
with a brand new, original one. The EPA intake
filter is guaranteed to make the vacuum cleaner
to work efficiently for ca. a year.
5 Place the SAFBAG­type bag into the chamber of the
vacuum cleaner.
6 Close the cover by pressing it, until you hear
a characteristic “click”.
D